TS522IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS522 |
| Pin Count | 8 |
| Operating Supply Voltage | 15V |
| Number of Channels | 2 |
| Operating Supply Current | 4mA |
| Nominal Supply Current | 5mA |
| Output Current | 37mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 250nA |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±2.5V~15V |
| Output Current per Channel | 37mA |
| Input Offset Voltage (Vos) | 850μV |
| Bandwidth | 15MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 9000 kHz |
| Voltage Gain | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Bias Current-Max (IIB) @25C | 0.75μA |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS522IDT Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. It comes in a Cut Tape (CT) case, which protects instrumentation amplifier from damage during delivery. The number of terminations approaches 8. A total of 8 pins are located on this board. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. This particular linear amplifier is a type of Operational Amplifier device, to be precise. 8 pins are included on the operational amplifiers. With regards to the offset voltage of the input, buffer amplifier is rated at 850μV. This electronic part is recommended for mounting type Surface Mount. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. As long as the supply current of the chip does not exceed 4mA, this op amp ic can operate. The voltage gain should stay at 100dB. As far as the device is concerned, buffer amplifier has 2 channels. The operating supply voltage of the buffer op amp is rated at 15V. TR is adopted to pack the instrumentation amplifier.
TS522IDT Features
8 Pins
supply voltage of 15V
100dB voltage gain
TS522IDT Applications
There are a lot of STMicroelectronics TS522IDT Instrumentational OP Amps applications.
- High input resistance broadband
- Signal filtering
- Power generator
- Test equipment
- Micro signal measurement
- Automatic control
- Medical instruments
- Biopotential
- High-frequency data acquisition systems
- single/dual op amp sum and difference circuits
