TS5A1066DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TS5A1066 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 50nA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 5.5 ns |
| Supply Type | Single |
| Bandwidth | 400MHz |
| Turn-Off Delay Time | 4.5 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 6.8pF 6.8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5.5ns, 4.5ns |
| Charge Injection | 1pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Drain to Source Resistance | 10Ohm |
| Normal Position | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A1066DBVR Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. This analog switch is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 5 terminations have been recorded. A high-quality output is provided by the electrical component's 1 channels. It is safe to turn on and run the electronic component with a 1.8V voltage supply. This electronic part can be found in the 5 series. Based on SPST - NO switching circuits, these analog multiplexers work. Try searching for the analog switch ic with TS5A1066 if you are looking for variants. Analog switches have 10Ohm internal resistance. For details about the functions of 5 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. A low voltage of 1.65V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 50nA current. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It is possible to transfer data over a 400MHz-bandwidth. A Drain to Source resistance of 10Ohm is shown for this electronic part.
TS5A1066DBVR Features
1 Channels
Switch Circuit: SPST - NO
50nA Supply Current
Bandwidth: 400MHz
Drain-to-Source resistance: 10Ohm
TS5A1066DBVR Applications
There are a lot of Texas Instruments TS5A1066DBVR Analog Switches & Multiplexers ICs applications.
- Fiber In The Loop (FITL)
- Digital cross connects (DSX-1)
- FTTH
- Audio/video switches
- Switching Systems
- T1/E1 Terminals
- Communication systems
- Industrial and process control systems
- Cable PC
- CSU
