TS5A1066DCKR
| Parameters | |
|---|---|
| Turn-Off Delay Time | 4.5 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 6.8pF 6.8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5.5ns, 4.5ns |
| Charge Injection | 1pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TS5A1066 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 50nA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 400MHz |
TS5A1066DCKR Overview
Due to its 5-TSSOP, SC-70-5, SOT-353 packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 1:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. There are 5 terminations totally. The electronic part delivers high-quality output through its 1 channels. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. As part of the design of the 5 series, this electronic part has been incorporated into the system. A SPST - NO switching circuit is used to build these analog multiplexers. Try searching for the analog switch ic with TS5A1066 if you are looking for variants. It has an internal resistance of 10Ohm. For details about the functions of 5 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. Users shouldn't supply more than 5.5V voltage to the switch device. The analog switch ic is of the Single supply type and is cost-effective. There should be 1.65V voltage fed to the electrical part below 1.65V. This multiplexer would work with 50nA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. This switch operates within the bandwidth of 400MHz.
TS5A1066DCKR Features
1 Channels
Switch Circuit: SPST - NO
50nA Supply Current
Bandwidth: 400MHz
TS5A1066DCKR Applications
There are a lot of Texas Instruments TS5A1066DCKR Analog Switches & Multiplexers ICs applications.
- Sample-and-hold systems
- Access Concentrators
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- RGB switches
- 65 V DACs
- Signal routing between systems
- Relay replacements
- DSLAMs
- Isolation
- Communications systems
