TS5A1066YZPR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-XFBGA, DSBGA |
| Number of Pins | 5 |
| Weight | 1.587573mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TS5A1066 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 50nA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 5.5 ns |
| Supply Type | Single |
| Bandwidth | 400MHz |
| Turn-Off Delay Time | 4.5 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 200nA |
| Channel Capacitance (CS(off), CD(off)) | 6.8pF 6.8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5.5ns, 4.5ns |
| Charge Injection | 1pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 500μm |
| Length | 1.75mm |
| Width | 1.25mm |
| Thickness | 310μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A1066YZPR Overview
Presented in 5-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. In total, 5 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 1.8V voltage supply. It is injected into the electrical part body with 5 pins. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Try searching for the analog switch ic with TS5A1066 if you are looking for variants. Internally, this switch multiplexer has a resistance of 10Ohm. For details about the functions of 5 pins, please refer to the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. It is recommended that the electrical component receives a voltage of 1.65V. The switch device would be able to operate with 50nA current. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. It is possible to transfer data over a 400MHz-bandwidth.
TS5A1066YZPR Features
1 Channels
Switch Circuit: SPST - NO
50nA Supply Current
Bandwidth: 400MHz
TS5A1066YZPR Applications
There are a lot of Texas Instruments TS5A1066YZPR Analog Switches & Multiplexers ICs applications.
- Cable Modem
- Signal routing between systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Sample-and-hold systems
- USB 1.1 signal switching circuits
- Microprocessor Controlled Analog Systems
- Digital Cross-Connects
- PBX interfaces
- Access Concentrators
- PBXs
