TS5A2066YZPR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFBGA, DSBGA |
| Number of Pins | 8 |
| Weight | 2.296311mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TS5A2066 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 100nA |
| Nominal Supply Current | 100nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 6.4 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 4.9 ns |
| On-State Resistance (Max) | 10Ohm |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 30nA |
| Channel Capacitance (CS(off), CD(off)) | 5.5pF 5.5pF |
| On-state Resistance Match-Nom | 0.9Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 5.8ns, 3.6ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -68dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 11.5ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 500μm |
| Length | 1.25mm |
| Width | 2.25mm |
| Thickness | 310μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A2066YZPR Overview
Packed in 8-XFBGA, DSBGA, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. There are 8 terminations totally. The electronic part delivers high-quality output through its 2 channels. When the electronic component is given a voltage of 1.8V, it should be turned on and run. A total of 8 pins are injected into the electrical part body. Multiplexers built on a SPST - NO switching circuit are built. Try searching for TS5A2066 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 10Ohm. You can find the functions of the 8 pins in the datasheets. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Single supply type analogue multiplexer. 1.65V is the lowest voltage that should be fed to the electronic electronic part. In order to operate this switch device, it would need a current of 100nA. Using a single voltage supply, this switch device consumes 1.65V~5.5V volts. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. The data can be transferred over a wide range of bandwidths, called 300MHz bandwidths.
TS5A2066YZPR Features
2 Channels
Switch Circuit: SPST - NO
100nA Supply Current
Bandwidth: 300MHz
TS5A2066YZPR Applications
There are a lot of Texas Instruments TS5A2066YZPR Analog Switches & Multiplexers ICs applications.
- SONET
- Access Concentrators
- Medical Instrumentation
- USB 1.1 signal switching circuits
- Fault Tolerant Systems
- Transmit
- Data Acquisition Systems
- HDTV
- Frame Relay Equipment
- Precision test equipment
