TS5A22362DRCR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 10-VFDFN Exposed Pad |
| Number of Pins | 10 |
| Weight | 26.109911mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 650mOhm |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TS5A22362 |
| Pin Count | 10 |
| Number of Outputs | 4 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.3V |
| Operating Supply Current | 200nA |
| Nominal Supply Current | 200nA |
| Max Supply Current | 1.3μA |
| Turn On Delay Time | 80 ns |
| Number of Inputs | 2 |
| Supply Type | Single |
| Bandwidth | 18.3MHz |
| Turn-Off Delay Time | 70 ns |
| On-State Resistance (Max) | 740mOhm |
| High Level Output Current | 150mA |
| Low Level Output Current | 150mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 66 dB |
| Current - Leakage (IS(off)) (Max) | 50nA |
| Channel Capacitance (CS(off), CD(off)) | 70pF |
| On-state Resistance Match-Nom | 0.023Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 80ns, 70ns |
| Charge Injection | 10pC |
| Channel-to-Channel Matching (ΔRon) | 40m Ω |
| Crosstalk | -78dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.3V~5.5V |
| Height | 1mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A22362DRCR Overview
Shipping overseas is convenient due to the electrical component's packing in 10-VFDFN Exposed Pad. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 2:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. The total number of terminations is 10. A 1 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 2.5V voltage supply. There are 10 pins injected into the electronic part body. SPDT switching circuits are used in these analog switch ics. Look for analog switch ic variants by searching with TS5A22362. As far as internal resistance is concerned, it has 650mOhm. To find out what the 10 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Analog switch ics with Single supply type are cost-effective. 2.3V is the lowest voltage that should be fed to the electronic electronic part. 200nA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2.3V~5.5V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 1.3μA, damage can occur. It is possible to operate 2 inputs. 18.3MHz bandwidths enable data to be transferred. The analog switch ics includes 4 outputs.
TS5A22362DRCR Features
1 Channels
Switch Circuit: SPDT
200nA Supply Current
Bandwidth: 18.3MHz
TS5A22362DRCR Applications
There are a lot of Texas Instruments TS5A22362DRCR Analog Switches & Multiplexers ICs applications.
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- ATM
- Sample-and-hold systems
- Intelligent PBX
- DSUs
- New designs requiring multiplexer functions
- Microprocessor controlled systems
- High speed data transmission line cards
- Video switching
- Avionics test equipment
