Parameters |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Signal Current-Max |
0.1A |
Height |
600μm |
Length |
1.5mm |
Width |
2mm |
Thickness |
550μm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-UFQFN |
Number of Pins |
10 |
Weight |
7.002332mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
900mOhm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Additional Feature |
VIDEO APPLICATION |
Subcategory |
Multiplexer or Switches |
Terminal Position |
QUAD |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
1.8V |
Terminal Pitch |
0.5mm |
Base Part Number |
TS5A23159 |
Pin Count |
10 |
Number of Outputs |
4 |
Power Supplies |
1.8/5V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Max Supply Current |
50nA |
Turn On Delay Time |
16.5 ns |
Number of Inputs |
2 |
Supply Type |
Single |
Bandwidth |
100MHz |
Turn-Off Delay Time |
8 ns |
On-State Resistance (Max) |
900mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
64 dB |
Current - Leakage (IS(off)) (Max) |
20nA |
Channel Capacitance (CS(off), CD(off)) |
18pF |
On-state Resistance Match-Nom |
0.15Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
13ns, 8ns |
Charge Injection |
-7pC |
Channel-to-Channel Matching (ΔRon) |
50m Ω |
Crosstalk |
-64dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
55ns |
TS5A23159RSERG4 Overview
Shipping overseas is convenient due to the electrical component's packing in 10-UFQFN. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. In Surface Mount, you'll find this switch device. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. Total terminations are 10. A 2 channel electronic part produces high-quality output. With a 1.8V voltage supply, the electrical component should be turned on and run. It is part of the design of the 10 series that this electronic component is included. A SPDT switching circuit is used to build these analog multiplexers. Try searching for TS5A23159 variants of the analog switch ic. In this multiplexer, the internal resistance is 900mOhm. To find out what the 10 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Analogue multiplexers of the Single supply type that are cost-effective. 1.65V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 10nA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. If you put voltage higher than 50nA on the digital multiplexer, damage may occur. In order to operate the 2 inputs, there are several steps to follow. A 100MHz-bandwidth can be used for data transfer. This electrical component also includes additional features such as VIDEO APPLICATION. 4 outputs are included in the analogue multiplexer.
TS5A23159RSERG4 Features
2 Channels
Switch Circuit: SPDT
10nA Supply Current
Bandwidth: 100MHz
Additional Features: VIDEO APPLICATION
TS5A23159RSERG4 Applications
There are a lot of Texas Instruments TS5A23159RSERG4 Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- Digital cross connects (DSX-1)
- DSUs
- RGB switches
- Communication systems
- Fiber In The Loop (FITL)
- Audio signal routing
- Signal routing between systems
- Cable PC
- Channelized and Unchannelized DS3 applications