TS5A26542YZTR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Contact Plating | Copper, Silver, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 12-UFBGA, DSBGA |
| Number of Pins | 12 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 750mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TS5A26542 |
| Pin Count | 12 |
| Number of Outputs | 4 |
| Polarity | Non-Inverting |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.25V |
| Operating Supply Current | 5.5nA |
| Nominal Supply Current | 5.5nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Bandwidth | 43MHz |
| Turn-Off Delay Time | 20 ns |
| On-State Resistance (Max) | 750mOhm |
| High Level Output Current | 450mA |
| Low Level Output Current | 450mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 37pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 25ns, 20ns |
| Charge Injection | 15pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -63dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.25V~5.5V |
| Height | 625μm |
| Length | 0m |
| Width | 0m |
| Thickness | 480μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A26542YZTR Overview
Presented in 12-UFBGA, DSBGA, this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. 12 terminations have been made so far. The electronic part delivers high-quality output through its 2 channels. When a voltage supply of 2.5V is used, the electronic component should be turned on and run. 12 pins are injected to the electronic part body. Multiplexers built on a SPDT switching circuit are built. Search with TS5A26542 if you are looking for analog multiplexer variants. This digital multiplexer has 750mOhm internal resistance. Please refer to the datasheets for 12 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. Single supply type digital switch with a low cost. The lowest voltage the electronic part should receive is 2.25V. The switch device would be able to operate with 5.5nA current. A voltage of 2.25V~5.5V is required to drain this analog switch from a single voltage supply. Put voltage above 100nA on the multiplexer to cause damage. The transfer of data can be performed over 43MHz bandwidths. There are 4 outputs on the analogue multiplexer.
TS5A26542YZTR Features
2 Channels
Switch Circuit: SPDT
5.5nA Supply Current
Bandwidth: 43MHz
TS5A26542YZTR Applications
There are a lot of Texas Instruments TS5A26542YZTR Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- PCMCIA cards
- Avionics
- DSLAMs
- Private Branch Exchange (PBX)
- Digital access cross connects
- Cell phones
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DSUs
- Audio/video switches
