TS5A3153YZPR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFBGA, DSBGA |
| Number of Pins | 8 |
| Weight | 2.296311mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 900mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TS5A3153 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 20nA |
| Nominal Supply Current | 20nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 9 ns |
| Supply Type | Single |
| Bandwidth | 97MHz |
| Turn-Off Delay Time | 12.5 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 64 dB |
| Channel Capacitance (CS(off), CD(off)) | 19pF 36pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 16ns, 15ns |
| Charge Injection | 12pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -64dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 63ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 500μm |
| Length | 1.25mm |
| Width | 2.25mm |
| Thickness | 310μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A3153YZPR Overview
Presented in 8-XFBGA, DSBGA, this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, you'll find this switch device. 2:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. In total, there have been 8 terminations. This electronic part offers high-quality output due to its 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Multiplexers built on a SPDT switching circuit are built. There are 1 circuits in this switch device. TS5A3153 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 900mOhm. You can find the functions of the 8 pins in the datasheets. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. In order for the electronic part to function properly, the lowest voltage should be 1.65V. The analogue multiplexer could operate on 20nA current. Draining from a single voltage supply, this analog switch requires a voltage of 1.65V~5.5V. If you put voltage higher than 100nA on the digital multiplexer, damage may occur. In 97MHz-bandwidths, data can be transferred. Multiplexer ics with 2 outputs are available.
TS5A3153YZPR Features
1 Channels
Switch Circuit: SPDT
20nA Supply Current
Bandwidth: 97MHz
TS5A3153YZPR Applications
There are a lot of Texas Instruments TS5A3153YZPR Analog Switches & Multiplexers ICs applications.
- Mechanical reed relay replacement
- CSU
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Avionics test equipment
- Signal routing between systems
- High speed data transmission line cards
- Automatic test equipment
- 65 V DACs
- Public switching systems
- RGB switches
