TS5A3154YZPR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-XFBGA, DSBGA |
| Number of Pins | 8 |
| Weight | 2.296311mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e1 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 900mOhm |
| Terminal Finish | Tin/Silver/Copper (Sn/Ag/Cu) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | BOTTOM |
| Terminal Form | BALL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TS5A3154 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 20nA |
| Nominal Supply Current | 20nA |
| Max Supply Current | 100nA |
| Turn On Delay Time | 8 ns |
| Supply Type | Single |
| Bandwidth | 100MHz |
| Turn-Off Delay Time | 12.5 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 64 dB |
| Channel Capacitance (CS(off), CD(off)) | 19pF 36pF |
| On-state Resistance Match-Nom | 0.16Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 16ns, 15ns |
| Charge Injection | 12pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -64dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-off Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 500μm |
| Length | 1.25mm |
| Width | 2.25mm |
| Thickness | 310μm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A3154YZPR Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-XFBGA, DSBGA. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 2:1 is the ratio of multiplexer to demultiplexer circuits. Around -40°C~85°C TA is the extended operating temperature. Total terminations are 8. A 1 channel electronic part produces high-quality output. When a voltage supply of 1.8V is used, the electronic component should be turned on and run. A total of 8 pins are injected into the electrical part body. On the other hand, analog switches can be constructed using SPDT switching circuits. There are 1 circuits in this switch device. Try searching for the analog switch ic with TS5A3154 if you are looking for variants. An switch multiplexer with 900mOhm internal resistance has a value of 900mOhm. Datasheets for 8 pin functions are available upon request. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. It is recommended that the electrical component receives a voltage of 1.65V. The analogue multiplexer could operate on 20nA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. The switch multiplexer may be damaged if it is exposed to voltage greater than 100nA. There are various bandwidths available for data transfer. There are 2 outputs on the analogue multiplexer.
TS5A3154YZPR Features
1 Channels
Switch Circuit: SPDT
20nA Supply Current
Bandwidth: 100MHz
TS5A3154YZPR Applications
There are a lot of Texas Instruments TS5A3154YZPR Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Medical Instrumentation
- Central office
- Voice over IP/DSL – Integrated Access Devices, Smart
- Fault Tolerant Systems
- PDAs
- Precision data acquisition
- RGB switches
- Channelized and Unchannelized DS3 applications
- Relay Replacement
