TS5A3159ADBVRE4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Weight | 6.492041mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 1.1Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Terminal Pitch | 0.95mm |
| Base Part Number | TS5A3159 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 100nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 50nA |
| Turn On Delay Time | 70 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 100MHz |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 64 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 18pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 30ns, 20ns |
| Charge Injection | -20pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -64dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A3159ADBVRE4 Overview
Shipping overseas is convenient with the electronic component packed in SOT-23-6. High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 6 terminations. This electronic part offers high-quality output due to its 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. The electronic part body is injected with 6 pins. Circuits based on SPDT switching are used to construct these analog switch ics. Try searching with TS5A3159 if you're looking for variants. In this multiplexer, the internal resistance is 1.1Ohm. The functions of 6 pins can be found in the datasheets. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A cost-effective Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 1.65V. The switch device would be able to operate with 100nA current. A voltage of 1.65V~5.5V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 50nA on the digital multiplexer, damage may occur. Operating the 1 inputs requires 1 inputs. It is possible to transfer data over a 100MHz-bandwidth. In this digital multiplexer, there are 2 outputs.
TS5A3159ADBVRE4 Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
Bandwidth: 100MHz
TS5A3159ADBVRE4 Applications
There are a lot of Texas Instruments TS5A3159ADBVRE4 Analog Switches & Multiplexers ICs applications.
- Medical
- Wireless Local Loop
- Fault Tolerant Systems
- PBX interfaces
- Digital cross connects (DSX-1)
- Communication systems
- Avionics and Military Systems
- Intelligent PBX
- High-Voltage
- Cellular phones
