Parameters |
Weight |
2.494758mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
6 |
Resistance |
1.1Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
1.8V |
Base Part Number |
TS5A3159 |
Output |
SEPARATE OUTPUT |
Pin Count |
6 |
Number of Channels |
1 |
Number of Circuits |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
100nA |
Nominal Supply Current |
10nA |
Max Supply Current |
50nA |
Turn On Delay Time |
35 ns |
Supply Type |
Single |
Bandwidth |
100MHz |
Turn-Off Delay Time |
30 ns |
On-State Resistance (Max) |
900mOhm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
64 dB |
Current - Leakage (IS(off)) (Max) |
20nA |
Channel Capacitance (CS(off), CD(off)) |
18pF |
On-state Resistance Match-Nom |
0.15Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
30ns, 20ns |
Charge Injection |
-20pC |
Channel-to-Channel Matching (ΔRon) |
50m Ω |
Crosstalk |
-64dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
75ns |
Switch-off Time-Max |
50ns |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Height |
1.1mm |
Length |
2mm |
Width |
1.25mm |
Thickness |
900μm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 2 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
6-TSSOP, SC-88, SOT-363 |
Number of Pins |
6 |
TS5A3159ADCKRG4 Overview
Packed in 6-TSSOP, SC-88, SOT-363, the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Around -40°C~85°C TA is the extended operating temperature. A total of 6 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 1.8V volts, the electrical component should be turned on and run. As part of its design, the 6 series is equipped with this electronic component. These analog multiplexers are built based on SPDT switching circuits. There are 1 circuits in this multiplexer. Use TS5A3159 to search for variants of the digital switches. Analog switches have 1.1Ohm internal resistance. To find out what the 6 pins do, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 1.65V. An operating current of 100nA would be sufficient for this switch device. This analogue multiplexer requires a voltage of 1.65V~5.5V when it drains from a single voltage supply. If you put voltage higher than 50nA on the digital multiplexer, damage may occur. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. The transfer of data can be performed over 100MHz bandwidths.
TS5A3159ADCKRG4 Features
1 Channels
Switch Circuit: SPDT
100nA Supply Current
Bandwidth: 100MHz
TS5A3159ADCKRG4 Applications
There are a lot of Texas Instruments TS5A3159ADCKRG4 Analog Switches & Multiplexers ICs applications.
- Imaging
- SONET
- Remote wireless modules
- USB 1.1 signal switching circuits
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Automotive applications
- Avionics and Military Systems
- Communications systems
- MP3 players
- Microprocessor controlled systems