TS5A3160DCKRG4
| Parameters | |
|---|---|
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 900mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TS5A3160 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 50nA |
| Turn On Delay Time | 24 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 100MHz |
| Turn-Off Delay Time | 27 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 64 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 18pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 6ns, 13ns |
| Charge Injection | 36.5pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -64dB @ 10MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-off Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
TS5A3160DCKRG4 Overview
The electronic component is convenient to ship overseas because it is packed in a 6-TSSOP, SC-88, SOT-363. The advanced packaging method Tape & Reel (TR) provides high reliability. In Surface Mount, you'll find this switch device. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operating temperature extended to -40°C~85°C TA. In total, 6 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 6 series that this electronic component is included. Circuits based on SPDT switching are used to construct these analog switch ics. Search with TS5A3160 if you are looking for analog multiplexer variants. Analog switches have 900mOhm internal resistance. Datasheets for 6 pin functions are available upon request. It is a typical Multiplexer or Switches analog multiplexer. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. 1.65V is the lowest voltage the electrical component should receive. 10nA current would be enough for this multiplexer to operate. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. Put voltage above 50nA on the multiplexer to cause damage. There are 1 inputs to be operated. 100MHz bandwidths enable data to be transferred. An output of 2 is provided by the digital multiplexer.
TS5A3160DCKRG4 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
Bandwidth: 100MHz
TS5A3160DCKRG4 Applications
There are a lot of Texas Instruments TS5A3160DCKRG4 Analog Switches & Multiplexers ICs applications.
- Cross Connects
- PBXs
- Digital Cross-Connects
- Industrial
- FTTH
- Fiber to the Home
- Access Concentrators
- ATM
- Fault Tolerant Systems
- New designs requiring multiplexer functions
