Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Contact Plating |
Gold |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
5-TSSOP, SC-70-5, SOT-353 |
Number of Pins |
5 |
Weight |
2.494758mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
900mOhm |
Subcategory |
Multiplexer or Switches |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
1.8V |
Frequency |
200MHz |
Base Part Number |
TS5A3166 |
Pin Count |
5 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
10nA |
Nominal Supply Current |
1nA |
Max Supply Current |
100nA |
Throw Configuration |
SPST |
Turn On Delay Time |
7 ns |
Input Voltage (Max) |
7V |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
11.5 ns |
On-State Resistance (Max) |
900mOhm |
High Level Output Current |
200mA |
Low Level Output Current |
200mA |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
64 dB |
Current - Leakage (IS(off)) (Max) |
20nA |
Channel Capacitance (CS(off), CD(off)) |
19pF 18pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
7ns, 11.5ns |
Charge Injection |
1pC |
Switching |
MAKE-BEFORE-BREAK |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
Max Junction Temperature (Tj) |
150°C |
Drain to Source Resistance |
900mOhm |
Normal Position |
NO |
Ambient Temperature Range High |
85°C |
Height |
1.1mm |
Length |
2mm |
Width |
1.25mm |
Thickness |
900μm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TS5A3166DCKR Overview
Shipping overseas is convenient due to the electrical component's packing in 5-TSSOP, SC-70-5, SOT-353. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. 5 terminations have been made so far. A 1 channel electronic part produces high-quality output. A 1.8V voltage supply should turn on and run the electronic component. The electronic part body is injected with 5 pins. SPST - NO switching circuits are used in these analog switch ics. Try searching with TS5A3166 if you're looking for variants. Analog switches have 900mOhm internal resistance. To find out what the functions of 5 pins are, please refer to their datasheets. It is a typical Multiplexer or Switches analog multiplexer. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Single supply type digital switch with a low cost. There should be 1.65V voltage fed to the electrical part below 1.65V. The switch device would be able to operate with 10nA current. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. When the digital multiplexer is charged above 100nA, damage can occur. In 200MHz-bandwidths, data can be transferred. There is 900mOhm resistance between Drain and Source for this electronic part.
TS5A3166DCKR Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Bandwidth: 200MHz
Drain-to-Source resistance: 900mOhm
TS5A3166DCKR Applications
There are a lot of Texas Instruments TS5A3166DCKR Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Channel Banks
- Data Acquisition Systems
- T1/E1 Terminals
- DVD-R
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Ultrasound
- SONET/SDH ADM
- Low-Voltage
- Industrial control systems