Parameters |
Normal Position |
NO |
Height |
1.1mm |
Length |
2mm |
Width |
1.25mm |
Thickness |
900μm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 6 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
5-TSSOP, SC-70-5, SOT-353 |
Number of Pins |
5 |
Weight |
2.494758mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
Resistance |
900mOhm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
1.8V |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
TS5A3166 |
Output |
SEPARATE OUTPUT |
Pin Count |
5 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.65V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Max Supply Current |
100nA |
Throw Configuration |
SPST |
Turn On Delay Time |
19 ns |
Input Voltage (Max) |
7V |
Number of Inputs |
1 |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
17.5 ns |
On-State Resistance (Max) |
900mOhm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
64 dB |
Current - Leakage (IS(off)) (Max) |
20nA |
Channel Capacitance (CS(off), CD(off)) |
19pF 18pF |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
7ns, 11.5ns |
Charge Injection |
1pC |
Switching |
MAKE-BEFORE-BREAK |
Voltage - Supply, Single (V+) |
1.65V~5.5V |
TS5A3166DCKRE4 Overview
As the electronic part is packed in 5-TSSOP, SC-70-5, SOT-353, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. 5 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. An 1.8V voltage supply should allow the electrical part to be turned on and run. Into the electrical component body are injected 5 pins. SPST - NO switching circuits are used in these analog switch ics. Search with TS5A3166 if you are looking for analog multiplexer variants. This digital multiplexer has 900mOhm internal resistance. The functions of 5 pins can be found in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. A cost-effective Single supply type analogue multiplexer. 1.65V is the lowest voltage the electrical component should receive. This digital switch can be operated with a current of 10nA. Using only a single voltage supply, this analog switch requires 1.65V~5.5V voltage. A voltage higher than 100nA may cause damage to the switch multiplexer. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. In order to operate the 1 inputs, there are several steps to follow. The transfer of data can be performed over 200MHz bandwidths.
TS5A3166DCKRE4 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Bandwidth: 200MHz
TS5A3166DCKRE4 Applications
There are a lot of Texas Instruments TS5A3166DCKRE4 Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- FTTH
- SDH
- Microprocessor controlled systems
- RGB switches
- High speed data transmission line cards
- Fiber In The Loop (FITL)
- Fiber to the Home
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Low-Voltage