TS5A3166DCKRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 900mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TS5A3166 |
| Output | SEPARATE OUTPUT |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10nA |
| Max Supply Current | 100nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 7 ns |
| Input Voltage (Max) | 7V |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 11.5 ns |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 62 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 19pF 18pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 7ns, 11.5ns |
| Charge Injection | 1pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A3166DCKRG4 Overview
This electronic part is conveniently packaged in 5-TSSOP, SC-70-5, SOT-353, making it easy to ship abroad. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~85°C TA is the extended operating temperature. The total number of terminations is 5. This electronic part offers high-quality output due to its 1 channels. An 1.8V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 5 series. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for the analog switch ic with TS5A3166 if you are looking for variants. In this multiplexer, the internal resistance is 900mOhm. The datasheets for the 5 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. 1.65V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 10nA would be sufficient for this switch device. Analogue multiplexers require a 1.65V~5.5V voltage to drain from a single voltage supply. When the digital multiplexer is charged above 100nA, damage can occur. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Among the inputs that can be operated are the 1 inputs. It is possible to transfer data over a 200MHz-bandwidth.
TS5A3166DCKRG4 Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Bandwidth: 200MHz
TS5A3166DCKRG4 Applications
There are a lot of Texas Instruments TS5A3166DCKRG4 Analog Switches & Multiplexers ICs applications.
- Residential Gateways, Home Gateway/Router
- Microprocessor controlled systems
- SONET/SDH ADM
- Communication systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Access Concentrators
- Imaging
- Remote Powered Equipment
- Fiber to the Home
- PBX interfaces
