TS5A4595DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 8Ohm |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TS5A4595 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 250nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 17 ns |
| Supply Type | Single |
| Bandwidth | 450MHz |
| Turn-Off Delay Time | 14 ns |
| On-State Resistance (Max) | 8Ohm |
| High Level Output Current | 20mA |
| Low Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 82 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6.5pF 6.5pF |
| On-state Resistance Match-Nom | 16Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 17ns, 14ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A4595DBVR Overview
Due to its SC-74A, SOT-753 packaging, the electronic part is convenient for international shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Mounted in Surface Mount is this multiplexer. There is 1:1 ratio between the number of multiplexers and demultiplexers. Temperatures around -40°C~85°C TA are extended for operation. A total of 5 terminations have been recorded. Due to its 1 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. 5 pins are injected to the electronic part body. A SPST - NC switching circuit is used for these analog switches. Look for analog switch ic variants by searching with TS5A4595. Internally, this switch multiplexer has a resistance of 8Ohm. Datasheets for functions of 5 pins are available. Theswitch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. In order for the electronic part to function properly, the lowest voltage should be 2V. In order to operate this switch device, it would need a current of 10nA. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. When the digital multiplexer is charged above 250nA, damage can occur. This switch operates within the bandwidth of 450MHz.
TS5A4595DBVR Features
1 Channels
Switch Circuit: SPST - NC
10nA Supply Current
Bandwidth: 450MHz
TS5A4595DBVR Applications
There are a lot of Texas Instruments TS5A4595DBVR Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Medical
- Frame Relay Equipment
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Industrial control systems
- Signal routing between systems
- USB 1.1 signal switching circuits
- Communication systems
- Ultrasound
- Optical Applications
