TS5A4596DCKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 8Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TS5A4596 |
| Output | COMMON OUTPUT |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 250nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 17 ns |
| Supply Type | Single |
| Bandwidth | 450MHz |
| Turn-Off Delay Time | 14 ns |
| On-State Resistance (Max) | 8Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 85 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6.5pF 6.5pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 17ns, 14ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A4596DCKR Overview
This electronic part is conveniently packaged in 5-TSSOP, SC-70-5, SOT-353, making it easy to ship abroad. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. Total terminations are 5. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. It is part of the design of the 5 series that this electronic component is included. A SPST - NO switching circuit is used for these analog switches. Try searching for the analog switch ic with TS5A4596 if you are looking for variants. The internal resistance of this digital multiplexer is 8Ohm. Datasheets for functions of 5 pins are available. There is Multiplexer or Switches analog multiplexer like this in the world. Users shouldn't supply more than 5.5V voltage to the switch device. Single supply type digital switch with a low cost. 2V is the lowest voltage that should be fed to the electronic electronic part. The switch device would be able to operate with 10nA current. This analog switch requires a voltage of 2V~5.5V to drain from a single voltage supply. Put voltage above 250nA on the multiplexer to cause damage. It is possible to use COMMON OUTPUT outputs on this digital multiplexer. It is possible to transfer data over a 450MHz-bandwidth.
TS5A4596DCKR Features
1 Channels
Switch Circuit: SPST - NO
10nA Supply Current
Bandwidth: 450MHz
TS5A4596DCKR Applications
There are a lot of Texas Instruments TS5A4596DCKR Analog Switches & Multiplexers ICs applications.
- DSUs
- Fiber In The Loop (FITL)
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channel Banks
- DVD-R
- MP3 players
- Transmit
- Fault Tolerant Systems
- Frame Relay Equipment
- Remote wireless modules
