TS5A4597DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 8Ohm |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | TS5A4597 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 250nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 17 ns |
| Supply Type | Single |
| Bandwidth | 450MHz |
| Turn-Off Delay Time | 14 ns |
| On-State Resistance (Max) | 8Ohm |
| High Level Output Current | 20mA |
| Low Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 85 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 6.5pF 6.5pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 17ns, 14ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 30ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NC |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A4597DBVR Overview
Shipping overseas is convenient due to the electrical component's packing in SC-74A, SOT-753. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Increasing operating temperature to around -40°C~85°C TA. In total, 5 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. The electronic part body is injected with 5 pins. Unlike digital switches, these are based on SPST - NC switching circuits. Try searching for TS5A4597 variants of the analog switch ic. Analog switches have 8Ohm internal resistance. Datasheets for functions of 5 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. 10nA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. If you put voltage higher than 250nA on the digital multiplexer, damage may occur. It is possible to transfer data over a 450MHz-bandwidth.
TS5A4597DBVR Features
1 Channels
Switch Circuit: SPST - NC
10nA Supply Current
Bandwidth: 450MHz
TS5A4597DBVR Applications
There are a lot of Texas Instruments TS5A4597DBVR Analog Switches & Multiplexers ICs applications.
- DVD-R
- Microprocessor controlled systems
- Video signal routing
- T1/E1 Terminals
- Power routing
- Medical systems
- DSUs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Private Branch Exchange (PBX)
- Voice over IP/DSL – Integrated Access Devices, Smart
