Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 3 days ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
5-TSSOP, SC-70-5, SOT-353 |
Number of Pins |
5 |
Weight |
2.494758mg |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
8Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Base Part Number |
TS5A4597 |
Output |
COMMON OUTPUT |
Pin Count |
5 |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2V |
Operating Supply Current |
10nA |
Nominal Supply Current |
10nA |
Max Supply Current |
250nA |
Throw Configuration |
SPST |
Turn On Delay Time |
17 ns |
Supply Type |
Single |
Bandwidth |
450MHz |
Turn-Off Delay Time |
14 ns |
On-State Resistance (Max) |
8Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
85 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
6.5pF 6.5pF |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
17ns, 14ns |
Charge Injection |
2pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
30ns |
Voltage - Supply, Single (V+) |
2V~5.5V |
Normal Position |
NC |
Height |
1.1mm |
Length |
2mm |
Width |
1.25mm |
Thickness |
900μm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
TS5A4597DCKR Overview
Shipping overseas is convenient due to the electrical component's packing in 5-TSSOP, SC-70-5, SOT-353. High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. In total, 5 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. As part of the design of the 5 series, this electronic part has been incorporated into the system. The analog switch ics are built using SPST - NC switching circuits. If you are looking for variants of the digital switch, trying search with TS5A4597. As far as internal resistance is concerned, it has 8Ohm. The datasheets for the 5 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. An effective Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 2V. This multiplexer would work with 10nA current. Using a single voltage supply, this switch device consumes 2V~5.5V volts. A digital multiplexer may suffer damage if voltage is applied above 250nA. A total of COMMON OUTPUT outputs are available on this analog switch ic. The data can be transferred over a wide range of bandwidths, called 450MHz bandwidths.
TS5A4597DCKR Features
1 Channels
Switch Circuit: SPST - NC
10nA Supply Current
Bandwidth: 450MHz
TS5A4597DCKR Applications
There are a lot of Texas Instruments TS5A4597DCKR Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- HDTV
- Cell phones
- Digital access cross connects
- Communication systems
- Battery Powered Instruments
- Voice over IP/DSL – Integrated Access Devices, Smart
- Microprocessor Controlled Analog Systems
- Residential Gateways, Home Gateway/Router
- Wireless Local Loop