TS5A4624DCKTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 900mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | TS5A4624 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.65V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 50nA |
| Turn On Delay Time | 25 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 100MHz |
| Turn-Off Delay Time | 10 ns |
| -3db Bandwidth | 90MHz |
| On-State Resistance (Max) | 900mOhm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 63 dB |
| Current - Leakage (IS(off)) (Max) | 20nA |
| Channel Capacitance (CS(off), CD(off)) | 18pF |
| On-state Resistance Match-Nom | 0.15Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 22ns, 8ns |
| Charge Injection | 15.5pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -63dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 70ns |
| Voltage - Supply, Single (V+) | 1.65V~5.5V |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A4624DCKTG4 Overview
Presented in 6-TSSOP, SC-88, SOT-363, this electrical component is convenient for overseas shipping. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there have been 6 terminations. As a result of its 1 channels, this electronic component provides high-quality output. Powered by a 1.8V voltage supply, the electrical part should be switched on and run. A total of 6 pins are injected into the body of the electronic part. Circuits based on SPDT switching are used to construct these analog switch ics. If you are looking for variants of the digital switch, trying search with TS5A4624. There is 900mOhm internal resistance in this digital multiplexer. Datasheets for functions of 6 pins are available. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. 1.65V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 10nA current. This analog switch requires a voltage of 1.65V~5.5V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 50nA. A 1 input needs to be operated. There are various bandwidths available for data transfer. Multiplexer ics with 2 outputs are available.
TS5A4624DCKTG4 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
-3db Bandwidth: 90MHz
Bandwidth: 100MHz
TS5A4624DCKTG4 Applications
There are a lot of Texas Instruments TS5A4624DCKTG4 Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- E1 Multiplexer
- Multi-Line E1 Interface Cards
- Microwave transmission systems
- CSU
- Fiber In The Loop (FITL)
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Digital Cross-Connects
- Cross Connects
- E1 Network Equipment
