TS5A9411DCKR

9ns, 7ns SPDT 9Ohm DUAL Analog Switches BREAK-BEFORE-MAKE TS5A9411 6 Pins 500pA 2.5V 6-TSSOP, SC-88, SOT-363

Manufacturer: Texas Instruments
Nocochips NO: 815-TS5A9411DCKR
Package: 6-TSSOP, SC-88, SOT-363
Datasheet: -
Stock: 271
Description: 9ns, 7ns SPDT 9Ohm DUAL Analog Switches BREAK-BEFORE-MAKE TS5A9411 6 Pins 500pA 2.5V 6-TSSOP, SC-88, SOT-363(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 2 days ago)
Contact Plating	Gold
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	6-TSSOP, SC-88, SOT-363
Number of Pins	6
Weight	2.494758mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
ECCN Code	EAR99
Resistance	10Ohm
Subcategory	Multiplexer or Switches
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	2.5V
Base Part Number	TS5A9411
Pin Count	6
Number of Outputs	2
Polarity	Non-Inverting
Number of Channels	1
Max Supply Voltage	5.5V
Min Supply Voltage	2.25V
Operating Supply Current	10nA
Nominal Supply Current	10nA
Max Supply Current	500nA
Turn On Delay Time	10 ns
Number of Inputs	1
Supply Type	Single
Bandwidth	100MHz
Turn-Off Delay Time	7.5 ns
On-State Resistance (Max)	9Ohm
High Level Output Current	50mA
Low Level Output Current	50mA
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	84 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	3.5pF
On-state Resistance Match-Nom	0.06Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	9ns, 7ns
Charge Injection	12.5pC
Channel-to-Channel Matching (ΔRon)	30m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	9.5ns
Voltage - Supply, Single (V+)	2.25V~5.5V
Drain to Source Resistance	10Ohm
Height	1.1mm
Length	2mm
Width	1.25mm
Thickness	900μm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

TS5A9411DCKR Overview

The electronic part can be shipped overseas conveniently because it is packaged in 6-TSSOP, SC-88, SOT-363. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. 2:1 is the number of circuits in the multiplexer and demultiplexer. Around -40°C~85°C TA is the extended operating temperature. In total, there are 6 terminations. By its 1 channels, the electronic component provides high-quality output. If the voltage supply is 2.5V volts, the electrical component should be turned on and run. 6 pins are injected to the electronic part body. The analog switch ics are built using SPDT switching circuits. Look for analog switch ic variants by searching with TS5A9411. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. To find out what the functions of 6 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage fed to the electronic component should be 2.25V. For this digital switch to work, 10nA current would suffice. Analogue multiplexers require a 2.25V~5.5V voltage to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 500nA. Among the inputs that can be operated are the 1 inputs. The data can be transferred over a wide range of bandwidths, called 100MHz bandwidths. This electronic component presents a Drain to Source resistance of 10Ohm. The analogue multiplexer has 2 outputs.