TS5A9411DCKT

9ns, 7ns SPDT 9Ohm DUAL Analog Switches BREAK-BEFORE-MAKE TS5A9411 6 Pins 500pA 2.5V 6-TSSOP, SC-88, SOT-363

Manufacturer: Texas Instruments
Nocochips NO: 815-TS5A9411DCKT
Package: 6-TSSOP, SC-88, SOT-363
Datasheet: -
Stock: 949
Description: 9ns, 7ns SPDT 9Ohm DUAL Analog Switches BREAK-BEFORE-MAKE TS5A9411 6 Pins 500pA 2.5V 6-TSSOP, SC-88, SOT-363(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	ACTIVE (Last Updated: 3 days ago)
Contact Plating	Gold
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	6-TSSOP, SC-88, SOT-363
Number of Pins	6
Weight	2.494758mg
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e4
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	6
Termination	SMD/SMT
Resistance	10Ohm
Subcategory	Multiplexer or Switches
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	2.5V
Base Part Number	TS5A9411
Pin Count	6
Number of Outputs	2
Polarity	Non-Inverting
Number of Channels	1
Max Supply Voltage	5.5V
Min Supply Voltage	2.25V
Operating Supply Current	10nA
Nominal Supply Current	10nA
Max Supply Current	500nA
Turn On Delay Time	10 ns
Number of Inputs	1
Supply Type	Single
Bandwidth	100MHz
Turn-Off Delay Time	7.5 ns
On-State Resistance (Max)	9Ohm
High Level Output Current	50mA
Low Level Output Current	50mA
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	84 dB
Current - Leakage (IS(off)) (Max)	500pA
Channel Capacitance (CS(off), CD(off))	3.5pF
On-state Resistance Match-Nom	0.06Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	9ns, 7ns
Charge Injection	12.5pC
Channel-to-Channel Matching (ΔRon)	30m Ω
Crosstalk	-85dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Switch-off Time-Max	9.5ns
Voltage - Supply, Single (V+)	2.25V~5.5V
Drain to Source Resistance	10Ohm
Height	1.1mm
Length	2mm
Width	1.25mm
Thickness	900μm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Lead Free

TS5A9411DCKT Overview

Shipping overseas is convenient with the electronic component packed in 6-TSSOP, SC-88, SOT-363. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 6 terminations. A electrical component with 1 channels is capable of high-quality output. Powered by a 2.5V voltage supply, the electrical part should be switched on and run. 6 pins are injected to the electronic part body. The analog switch ics are built using SPDT switching circuits. Try searching with TS5A9411 to find analog multiplexer variants. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. For functions related to 6 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. 2.25V is the lowest voltage the electrical component should receive. An operating current of 10nA would be sufficient for this switch device. Draining from a single voltage supply, this analog switch requires a voltage of 2.25V~5.5V. Put voltage above 500nA on the multiplexer to cause damage. The electrical component supports 1 inputs. In 100MHz-bandwidths, data can be transferred. There is 10Ohm resistance between the Drain and Source on this part. In this digital multiplexer, there are 2 outputs.