TS5A9411DCKTG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| Resistance | 900mOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 2.5V |
| Base Part Number | TS5A9411 |
| Pin Count | 6 |
| Number of Outputs | 2 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.25V |
| Operating Supply Current | 10nA |
| Nominal Supply Current | 10nA |
| Max Supply Current | 500nA |
| Turn On Delay Time | 10 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 100MHz |
| Turn-Off Delay Time | 7.5 ns |
| On-State Resistance (Max) | 9Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 84 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF |
| On-state Resistance Match-Nom | 0.06Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 9ns, 7ns |
| Charge Injection | 12.5pC |
| Channel-to-Channel Matching (ΔRon) | 30m Ω |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 9.5ns |
| Voltage - Supply, Single (V+) | 2.25V~5.5V |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS5A9411DCKTG4 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 6-TSSOP, SC-88, SOT-363. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature around -40°C~85°C TA extended. Totally, there are 6 terminations. A high-quality output is provided by the electrical component's 1 channels. Turning on and running the electrical part should be easy with a 2.5V voltage supply. There is an electrical component included in the 6 series. SPDT switching circuits are used in these analog switch ics. Using the TS5A9411 search parameter, you can discover variants of the switch. This digital multiplexer has 900mOhm internal resistance. Datasheets for 6 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A cost-effective Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 2.25V. An operating current of 10nA would be sufficient for this switch device. A voltage of 2.25V~5.5V is required for this switch device, which drains from a single voltage source. When the digital multiplexer is charged above 500nA, damage can occur. Operating 1 inputs is required. The transfer of data can be performed over 100MHz bandwidths. The analog switch ics includes 2 outputs.
TS5A9411DCKTG4 Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
Bandwidth: 100MHz
TS5A9411DCKTG4 Applications
There are a lot of Texas Instruments TS5A9411DCKTG4 Analog Switches & Multiplexers ICs applications.
- DSLAMs
- Optical Applications
- SDH/SONET multiplexers
- E1 Multiplexer
- PDH Multiplexers
- Cellular phones
- Fault Tolerant Systems
- Fiber to the Home
- Channel Banks
- New designs requiring multiplexer functions
