TS912IDT
| Parameters | |
|---|---|
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Dual Supply Voltage | 5V |
| Max Junction Temperature (Tj) | 150°C |
| Ambient Temperature Range High | 125°C |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS912 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 8V |
| Power Supplies | 3/10V |
| Number of Channels | 2 |
| Operating Supply Current | 400μA |
| Nominal Supply Current | 700μA |
| Output Current | 40mA |
| Slew Rate | 1.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1.4MHz |
| Unity Gain BW-Nom | 800 kHz |
| Voltage Gain | 92.04dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Current - Output / Channel | 75mA |
| Low-Bias | YES |
TS912IDT Overview
A 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used to deliver the buffer op amp. During the past two weeks, there have been close to 8 terminations. Buffer amplifier has a total of 8 pins on it. Please take in mind that op amp should be run at 3V. It should be noted that this op amp is a type of Operational Amplifier device. In total, the buffer amplifier consists of 8 pins. Op amp rates 10mV as input offset voltage. For this electronic part, it is recommended that you mount it with type Surface Mount. In terms of operating temperatures, this buffer amplifier works very well at a temperature of around -40°C~125°C . Using an 400μA supply current, this operational amplifier ics can be operated. Keeping the voltage gain at 92.04dB is the best course of action. 2 channels are available on the instrumentation amplifier. On the output type, there are Rail-to-Rail different types of op amps. The operating supply voltage of instrumentation amplifier is rated 8V voltage. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
TS912IDT Features
8 Pins
supply voltage of 3V
92.04dB voltage gain
Output Type: Rail-to-Rail
TS912IDT Applications
There are a lot of STMicroelectronics TS912IDT Instrumentational OP Amps applications.
- High speed sample
- Commercial audio systems
- Navigation
- Automotive sensors
- Multiplication circuits
- Hand-held batteries
- Non-polarized electrodes
- Radiation thermometry transducers
- High/low-pass filter circuit
- Weak signal detection
