TS972IDT
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS972 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 2mA |
| Nominal Supply Current | 5.6mA |
| Output Current | 100mA |
| Slew Rate | 4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 200nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 12MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Unity Gain BW-Nom | 12000 kHz |
| Voltage Gain | 80dB |
| Average Bias Current-Max (IIB) | 1μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.75μA |
| Programmable Power | NO |
| Dual Supply Voltage | 3V |
| Power | NO |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 2.5V |
TS972IDT Overview
In the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. An op amp ic of the General Purpose type. A Cut Tape (CT) case is used to deliver the buffer op amp. The number of terminations approaches 8. The pins on this board total to 8 in total. Please take in mind that op amp should be run at 2.5V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. The op amp ic has an array of 8 pins on it. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. This electrical part should be mounted using type Surface Mount. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. The buffer amplifier is capable of operating from a supply current of 2mA . 80dB should be the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of the buffer op amp is rated at 5V. The instrumentation amplifier is packed in the form of TAPE AND REEL.
TS972IDT Features
8 Pins
supply voltage of 2.5V
80dB voltage gain
Output Type: Rail-to-Rail
TS972IDT Applications
There are a lot of STMicroelectronics TS972IDT Instrumentational OP Amps applications.
- Ultrasound transducers
- PDA
- Tablets
- Strain gauges
- Active probe
- Video computer boards
- Thermocouples
- Hand-held batteries
- Blood pressure sensors
- Precision measurement
