TS974IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 2.5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS974 |
| Pin Count | 14 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 4 |
| Operating Supply Current | 2mA |
| Nominal Supply Current | 11.2mA |
| Output Current | 100mA |
| Min Input Voltage | 2.7V |
| Slew Rate | 4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 200nA |
| Max Input Voltage | 10V |
| Voltage - Supply, Single/Dual (±) | 2.7V~10V ±1.35V~5V |
| Output Current per Channel | 100mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 12MHz |
| Neg Supply Voltage-Nom (Vsup) | -2.5V |
| Unity Gain BW-Nom | 12000 kHz |
| Voltage Gain | 80dB |
| Average Bias Current-Max (IIB) | 1μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 1mV |
| Bias Current-Max (IIB) @25C | 0.75μA |
| Dual Supply Voltage | 3V |
| Height | 1.65mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS974IDT Overview
The linear amplifier is packaged in a 14-SOIC (0.154, 3.90mm Width) case. An op amp ic of the General Purpose type. Upon delivery, op amp ic is packaged in a Cut Tape (CT) case. The number of terminations is approaching the 14 mark. Buffer amplifier has a total of 14 pins on it. I would like to remind you that this buffer op amp should be powered by an 2.5V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. The op amp ic has an array of 14 pins on it. Op amp rates 5mV as input offset voltage. Surface Mount is the recommended mounting type for this linear amplifier. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Operational amplifier can operate supply current at 2mA. It is a member of the 80dB's 80dB family. As far as the device is concerned, buffer amplifier has 4 channels. In addition to outputting Rail-to-Rail signals, this op amp ic offers a number of other advantages. The operating supply voltage of the buffer op amp is rated at 5V. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
TS974IDT Features
14 Pins
supply voltage of 2.5V
80dB voltage gain
Output Type: Rail-to-Rail
TS974IDT Applications
There are a lot of STMicroelectronics TS974IDT Instrumentational OP Amps applications.
- Large motor controllers
- Digital cameras
- Biopotential
- Band-pass filter
- Differentiator circuits
- High-frequency data acquisition systems
- Blood pressure sensors
- Automotive sensors
- Semiconductor detectors
- Medical instruments
