TSH24IDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 500mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TSH24 |
| Pin Count | 14 |
| Operating Supply Voltage | 15V |
| Number of Channels | 4 |
| Operating Supply Current | 2.15mA |
| Nominal Supply Current | 2.15mA |
| Power Dissipation | 500mW |
| Output Current | 40mA |
| Slew Rate | 15V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 100nA |
| Voltage - Supply, Single/Dual (±) | 3V~30V ±1.5V~15V |
| Output Current per Channel | 37mA |
| Input Offset Voltage (Vos) | 3.5mV |
| Bandwidth | 25MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 25000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.65μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Voltage - Input Offset | 2.5mV |
| Bias Current-Max (IIB) @25C | 0.65μA |
| Max Junction Temperature (Tj) | 150°C |
| Height | 1.75mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TSH24IDT Overview
Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. A General Purpose-type buffer amplifier is shown here. A Cut Tape (CT) case is used to deliver the buffer op amp. In recent months, the number of terminations has approached 14. A total of 14 pins are located on this board. The linear amplifier should be run at 15V at all times, so please keep that in mind when using it. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. A total of 14 pins are present on the instrumentation amplifier. In terms of the input offset voltage, instrumentation amplifier rates at 3.5mV. The mounting type that is recommended for this electrical part is Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . In order for this instrumentation amplifier to operate, the supply current needs to be between 2.15mA and 10 . 100dB should be the voltage gain. On the buffer amps, there are 4 channels that can be used. The operating supply voltage of the buffer op amp is rated at 15V. It is used TAPE AND REEL to pack the op amps.
TSH24IDT Features
14 Pins
supply voltage of 15V
100dB voltage gain
TSH24IDT Applications
There are a lot of STMicroelectronics TSH24IDT Instrumentational OP Amps applications.
- Portable electronic products powered by batteries
- Addition operation circuits
- High input resistance broadband
- Information processing
- Radar
- Ultrasound transducers
- Mobile phone
- Switching amplifier
- Vehicle electronics
- Communication device
