banner_page

TSV994IDT

35mA per Channel 1pA 62 dB Instrumentational OP Amps 0.0001μA 2.5V~5.5V TSV994 14 Pins 14-SOIC (0.154, 3.90mm Width)


  • Manufacturer: STMicroelectronics
  • Nocochips NO: 761-TSV994IDT
  • Package: 14-SOIC (0.154, 3.90mm Width)
  • Datasheet: PDF
  • Stock: 321
  • Description: 35mA per Channel 1pA 62 dB Instrumentational OP Amps 0.0001μA 2.5V~5.5V TSV994 14 Pins 14-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time 1 Week
Lifecycle Status ACTIVE (Last Updated: 7 months ago)
Mount Surface Mount
Mounting Type Surface Mount
Package / Case 14-SOIC (0.154, 3.90mm Width)
Number of Pins 14
Operating Temperature -40°C~125°C
Packaging Tape & Reel (TR)
JESD-609 Code e4
Part Status Active
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 14
ECCN Code EAR99
Terminal Finish Nickel/Palladium/Gold (Ni/Pd/Au)
Subcategory Operational Amplifier
Packing Method TAPE AND REEL
Technology BICMOS
Terminal Position DUAL
Terminal Form GULL WING
Peak Reflow Temperature (Cel) 260
Number of Functions 4
Supply Voltage 3.3V
Terminal Pitch 1.27mm
Time@Peak Reflow Temperature-Max (s) 40
Base Part Number TSV994
Pin Count 14
Output Type Rail-to-Rail
Number of Elements 4
Power Supplies 3/5V
Operating Supply Current 820μA
Nominal Supply Current 4.4mA
Output Current 35mA
Slew Rate 10V/μs
Architecture VOLTAGE-FEEDBACK
Amplifier Type General Purpose
Common Mode Rejection Ratio 62 dB
Current - Input Bias 1pA
Voltage - Supply, Single/Dual (±) 2.5V~5.5V
Output Current per Channel 35mA
Input Offset Voltage (Vos) 4.5mV
Bandwidth 20MHz
Unity Gain BW-Nom 20000 kHz
Voltage Gain 91dB
Average Bias Current-Max (IIB) 0.0001μA
Low-Offset NO
Frequency Compensation YES
Supply Voltage Limit-Max 6V
Voltage - Input Offset 100μV
Low-Bias YES
Micropower NO
Bias Current-Max (IIB) @25C 0.00001μA
Programmable Power NO
Power NO
Height Seated (Max) 1.75mm
Length 8.65mm
Radiation Hardening No
RoHS Status ROHS3 Compliant
Lead Free Lead Free

TSV994IDT Overview


A 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. An op amp ic of the General Purpose type. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. A total of 14 terminations have been reported in the past few weeks. The total number of pins on linear amplifier is 14. It is important to remember that this op amp should be operated at a voltage of 3.3V volts. It should be noted that this op amp is a type of Operational Amplifier device. The op amp ic has an array of 14 pins on it. With regards to the offset voltage of the input, buffer amplifier is rated at 4.5mV. For this electrical component, Surface Mount is the recommended mounting type. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. As long as the supply current of the chip does not exceed 820μA, this op amp ic can operate. There should be no change in the voltage gain at 91dB. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. A voltage rating of 4 is indicated for the op amp's operating supply voltage. The instrumentation amplifier is packed in the form of TAPE AND REEL.

TSV994IDT Features


14 Pins
supply voltage of 3.3V
91dB voltage gain
Output Type: Rail-to-Rail

TSV994IDT Applications


There are a lot of STMicroelectronics TSV994IDT Instrumentational OP Amps applications.

  • Weighing systems
  • Signal transformation
  • Signal operation
  • Hand-held batteries
  • Blood pressure sensors
  • High-frequency data acquisition systems
  • Thermocouples
  • Scintillation detectors
  • Instrumentation
  • Weak signal detection

Write a review

Note: HTML is not translated!
    Bad           Good