TSX564IQ4T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-UFQFN |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C |
| Packaging | Digi-Reel® |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | QUAD |
| Number of Functions | 4 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.5mm |
| Base Part Number | TSX564 |
| Number of Channels | 4 |
| Operating Supply Current | 250μA |
| Nominal Supply Current | 250μA |
| Output Current | 92mA |
| Slew Rate | 1.1V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 76 dB |
| Current - Input Bias | 1pA |
| Max Input Voltage | 16V |
| Voltage - Supply, Single/Dual (±) | 3V~16V |
| Output Current per Channel | 92mA |
| Input Offset Voltage (Vos) | 1mV |
| Bandwidth | 900 kHz |
| Unity Gain BW-Nom | 800 kHz |
| Voltage Gain | 85dB |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Low-Bias | YES |
| Micropower | YES |
| Max Frequency | 10kHz |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Input Voltage Noise Density | 55nV/sqrt Hz |
| Height | 600μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TSX564IQ4T Overview
It is packaged in an 16-UFQFN-case that protects the operational amplifiers from damage. Buffer amps of this type are called General Purpose-types. The op amp is delivered to you in a Digi-Reel? case. In recent months, the number of terminations has approached 16. I would like to remind you that this buffer op amp should be powered by an 3.3V battery. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. 16 pins are included on the operational amplifiers. The input offset voltage is 1mV. The mounting type that is recommended for this electrical part is Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. You can run this op amp ic on 250μA . Maintain 85dB as the voltage gain. Buffer op amp is equipped with 4 channels on the device. To pack the operational amplifier ics, TAPE AND REEL is adopted as the packing method.
TSX564IQ4T Features
supply voltage of 3.3V
85dB voltage gain
TSX564IQ4T Applications
There are a lot of STMicroelectronics TSX564IQ4T Instrumentational OP Amps applications.
- Radar
- Test equipment
- earphone
- Commercial audio systems
- Hand-held batteries
- Inverse/same-phase proportional circuit
- Non-polarized electrodes
- Signal operation
- Video data acquisition
- Portable electronic products powered by batteries
