TSX922IYST
| Parameters | |
|---|---|
| Slew Rate | 17V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 72 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 4V~16V |
| Output Current per Channel | 74mA |
| Input Offset Voltage (Vos) | 4mV |
| Gain Bandwidth Product | 10MHz |
| Unity Gain BW-Nom | 9000 kHz |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Programmable Power | NO |
| Wideband | NO |
| Power | NO |
| Common-mode Reject Ratio-Min | 57 dB |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 2 |
| Supply Voltage | 4.5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | TSX922 |
| JESD-30 Code | S-PDSO-G8 |
| Output Type | Rail-to-Rail |
| Number of Circuits | 2 |
| Operating Supply Current | 2.8mA |
| Supply Current-Max | 3.5mA |
TSX922IYST Overview
It is packaged in an 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)-case that protects the operational amplifiers from damage. The instrumentation amplifier in this picture is of the General Purpose-type. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. The number of terminations is approaching the 8 mark. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 4.5V. A type of Operational Amplifier buffer op amp is what this device is specifically, to be more precise. As far as the input offset voltage is concerned, linear amplifier rates at 4mV. For this electrical component, Surface Mount is the recommended mounting type. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . Using a supply current of 2.8mA , this buffer op amp will be able to operate. There are 2 circuits on this op amp. This op amp ic outputs Rail-to-Rail signals, which is one of the many benefits it has. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted. As the name implies, Automotive, AEC-Q100 refers to the series of the buffer op amp.
TSX922IYST Features
supply voltage of 4.5V
Output Type: Rail-to-Rail
TSX922IYST Applications
There are a lot of STMicroelectronics TSX922IYST Instrumentational OP Amps applications.
- Biopotential
- Video conversion and routing
- Test equipment
- Blood pressure sensors
- High input resistance broadband
- Cinema or auditorium audio system
- earphone
- Power control
- Vehicle electronics
- Power generator
