UA741CDR
| Parameters | |
|---|---|
| Input Offset Current-Max (IIO) | 0.2μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Base Part Number | UA741 |
| Pin Count | 8 |
| Operating Supply Voltage | 18V |
| Number of Channels | 1 |
| Operating Supply Current | 1.7mA |
| Nominal Supply Current | 2.8mA |
| Power Dissipation | 500mW |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 80nA |
| Voltage - Supply, Single/Dual (±) | 7V~36V ±3.5V~18V |
| Output Current per Channel | 25mA |
| Input Offset Voltage (Vos) | 6mV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.5μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1mV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.5μA |
| Programmable Power | NO |
| Dual Supply Voltage | 9V |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 6mV |
UA741CDR Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp of this type is a General Purpose-type. The op amp is delivered to you in a Cut Tape (CT) case. The number of terminations approaches 8. Buffer amplifier has a total of 8 pins. Please take in mind that op amp should be run at 15V. I would like to specify that this buffer amplifier belongs to the Operational Amplifier-type of devices. Linear amplifier includes 8 pins. With regard to input offset voltage, instrumentation amplifier is rated at 6mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. With regard to operating temperature, op amp ranges 0°C~70°C. Operational amplifier can operate supply current at 1.7mA. Voltage gain should remain at 106.02dB. 1 channels are available on the instrumentation amplifier. The operating supply voltage of instrumentation amplifier is rated 18V voltage. As a result of this, the buffer amplifier is packed in TR.
UA741CDR Features
8 Pins
supply voltage of 15V
106.02dB voltage gain
UA741CDR Applications
There are a lot of Texas Instruments UA741CDR Instrumentational OP Amps applications.
- Professional videography
- Strain gauges
- Automation control systems
- Measurements of Wheatstone bridge
- Broadcasting
- Medical instruments
- Signal operation
- Integrator circuits
- Radar
- PDA
