UC2825ADWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 473.692182mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 16 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | CAN ALSO BE CONFIGURED IN CURRENT MODE |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 12V |
| Frequency | 1MHz |
| Base Part Number | UC2825 |
| Function | Step-Up, Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 2V |
| Output Type | Transistor Driver |
| Max Output Current | 2A |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 200mA |
| Voltage - Supply (Vcc/Vdd) | 8.4V~22V |
| Control Features | Current Limit, Frequency Control, Ramp, Soft Start |
| Input Voltage (Min) | 8.8V |
| Topology | Boost, Flyback, Forward Converter, Full-Bridge, Half-Bridge, Push-Pull |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 400kHz~1MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 20ns |
| Supply Current-Max (Isup) | 36mA |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 20 ns |
| Max Duty Cycle | 50 % |
| Input Current | 28mA |
| Output Phases | 1 |
| Height | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UC2825ADWG4 Overview
It comes in the 16-SOIC (0.295, 7.50mm Width) package, which makes switching controller suitable for most applications. dc motor controller is suitable for 2 output generation. There is a Tube solid enclosure around the pmic. With this function, you can deal with Transistor Driver dc switching's outputs (s). 8.4V~22V is the supply voltage and the operating voltage of the dc control. Worked in an dc switcher with a -40°C~85°C TA rating. With this switching controller, you can switch at 400kHz~1MHz. dc dc regulators can be carried out with Surface Mount. Switching control is made easier with the dcdc regulator's Current Limit, Frequency Control, Ramp, Soft Start. A SWITCHING CONTROLLER analog integrated circuit is connected to the switch converters. The switching converters's terminals (s) are designed at DUAL. 16 terminations with a variety of function. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. The DC switcher's nominal voltage is 12V. Searching "UC2825" will return other relevant dc to dc converter ics. 16 pins are on switching converter. Specifically, switching converter falls under the Switching Regulator or Controllers category. 8.8V should be the minimum input voltage for the dc dc voltage regulator. According to the test statistics, DC regulator outputs 2V voltage. It's important to remember that the dc dc regulator's normaloutput current is 200mA, so you should note it down when starting a new project. It is set to 50 % duty cycle to ensure voltage regulator dc to dc reliability during power-ups and power-downs. The switching controller works at a frequency of 1MHz. DC to DC voltage regulator has the value of CAN ALSO BE CONFIGURED IN CURRENT MODE to better satisfy the requirement. Voltage 12V is required for supply. DC switcher will not be able to provide an output current above 2A volts. The controller should not be supplied with more current than 36mA. An input of 28mA current flow could satisfy the operation of the switching converter .
UC2825ADWG4 Features
Transistor Driver Outputs
Switching Frequency: 400kHz~1MHz
Current Limit, Frequency Control, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
Frequency: 1MHz
CAN ALSO BE CONFIGURED IN CURRENT MODE
UC2825ADWG4 Applications
There are a lot of Texas Instruments UC2825ADWG4 DC to DC converter applications.
- Access control systems
- Flaw detection equipment
- Flexible manufacturing cells
- Computer-related products
- Special machining machine tools
- Planers
- Drilling machines
- Arc suppression circuits
- ATMs
- Machining centers
