UCC27200DDARG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Number of Pins | 8 |
| Weight | 70.590313mg |
| Packaging | Tape and Reel |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 140°C |
| Min Operating Temperature | -40°C |
| Subcategory | MOSFET Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Frequency | 1MHz |
| Pin Count | 8 |
| Max Output Current | 3mA |
| Operating Supply Voltage | 12V |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 17V |
| Min Supply Voltage | 8V |
| Power Dissipation-Max | 2.7W |
| Nominal Supply Current | 4mA |
| Power Dissipation | 2.7W |
| Max Supply Current | 4mA |
| Current - Output | 3A |
| Propagation Delay | 20 ns |
| Turn On Delay Time | 1 ns |
| Rise Time | 8ns |
| Fall Time (Typ) | 7 ns |
| Turn-Off Delay Time | 1 ns |
| Interface IC Type | HALF BRIDGE BASED PERIPHERAL DRIVER |
| Number of Drivers | 2 |
| Output Peak Current Limit-Nom | 3A |
| Built-in Protections | UNDER VOLTAGE |
| Output Current Flow Direction | SOURCE SINK |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
UCC27200DDARG4 Overview
A package of Tape and Reel has been used.Gate drivers is configured wGate driversh 2 drivers.The configuration starts with 8 terminations.The device is mounted using Surface Mount.At the time of design, it is configured with 8 pins.Mosfet driver is designed specifically to run on 12V volts of power.In this case, HALF BRIDGE BASED PERIPHERAL DRIVER serves as the interface IC.As a maximum, there is 3mA limit to the output current.Mosfet driver includes a number of useful electronic components in Mosfet drivers subcategory of MOSFET Drivers.There are 8 component pins on the board.There is a maximum value of 140°C for the allowable operating temperature.Temperatures below -40°C are allowable as a minimum.Mosfet gate drivers is recommended to keep the supply current at 4mA to ensure greater stabilMosfet gate driversy.The supply voltage of 17V is its maximum value for operation.In order for the device to function, the supply voltage must be set to 8V.Mosfet gate drivers outputs a current of 3A.A voltage of 12V should be set for the operating supply voltage.When 1MHz is used frequently, efficiency can be improved.
UCC27200DDARG4 Features
Embedded in the Tape and Reel package
2 drivers
8 pins
UCC27200DDARG4 Applications
There are a lot of Texas Instruments UCC27200DDARG4 gate drivers applications.
- High-voltage isolated DC-DC converters
- High-speed communications
- High current laser/LED systems
- Active filtering
- Motor Drives
- Video amplifiers
- 48 V to 12 V PoL Converters, 48 V to Low Voltage Bus Converter,
- Smart Phones
- High frequency line drivers
- Power factor correction (PFC) circuits
