UCC27201DDAG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Package / Case | SOIC |
| Number of Pins | 8 |
| Weight | 70.590313mg |
| Packaging | Rail/Tube |
| JESD-609 Code | e4 |
| Moisture Sensitivity Level (MSL) | 1 |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Operating Temperature | 140°C |
| Min Operating Temperature | -40°C |
| Subcategory | MOSFET Drivers |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Frequency | 1MHz |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Max Output Current | 3A |
| Operating Supply Voltage | 12V |
| Temperature Grade | AUTOMOTIVE |
| Max Supply Voltage | 17V |
| Min Supply Voltage | 8V |
| Power Dissipation-Max | 2.7W |
| Nominal Supply Current | 5.5mA |
| Power Dissipation | 2.7W |
| Max Supply Current | 5.5mA |
| Current - Output | 3A |
| Propagation Delay | 20 ns |
| Turn On Delay Time | 1 ns |
| Rise Time | 8ns |
| Fall Time (Typ) | 7 ns |
| Turn-Off Delay Time | 1 ns |
| Output Polarity | TRUE |
| Interface IC Type | HALF BRIDGE BASED PERIPHERAL DRIVER |
| Driver Number of Bits | 2 |
| Output Peak Current Limit-Nom | 3A |
| Built-in Protections | UNDER VOLTAGE |
| Output Current Flow Direction | SOURCE SINK |
| Height | 1.48mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
UCC27201DDAG4 Overview
There is greater flexibility with the SOIC package.Rail/Tube is the form of the package.Its configuration is based on a total of 8 terminations.The device is mounted with Surface Mount.At the time of design, it is configured with 8 pins.A voltage of 12V is required for its operation.There is an interface IC called HALF BRIDGE BASED PERIPHERAL DRIVER that is employed in this device.3A is the maximum output current.Several electronic components are included in its subcategory of MOSFET Drivers.The board contains 8 pins for component connections.The basis of this system consists of 2 outputs.Operating temperatures cannot exceed 140°C.Temperatures below -40°C are allowable as a minimum.To maintain higher stability, the supply current should always be 5.5mA.When the supply voltage is 17V, it is at its maximum operation.The supply voltage of 8V is its minimum value for operation.As a result, it outputs a 3A current.The operating supply voltage should be set at 12V.When 1MHz is used frequently, efficiency can be improved.
UCC27201DDAG4 Features
Embedded in the Rail/Tube package
8 pins
UCC27201DDAG4 Applications
There are a lot of Texas Instruments UCC27201DDAG4 gate drivers applications.
- Digitally controlled power supplies
- Telecom switch mode power supplies
- 48 V to 12 V PoL Converters, 48 V to Low Voltage Bus Converter,
- Video amplifiers
- DC/DC converters
- Isolated Supplies for controller area network (CAN),
- Industrial Power Supplies
- Commercial and agricultural vehicles (CAV)
- Uninterruptible Power Supplies (UPS)
- RGB applications
