UCC28084PWG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tray |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Frequency | 1MHz |
| Base Part Number | UCC28084 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 500mV |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 10V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 4.1V~15V |
| Control Features | Current Limit, Frequency Control |
| Input Voltage (Min) | 4.3V |
| Topology | Half-Bridge, Push-Pull |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 200kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 25ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 25 ns |
| Max Duty Cycle | 50 % |
| Duty Cycle (Max) | 49% |
| Clock Sync | No |
| Output Phases | 1 |
| Height | 1.2mm |
| Length | 3mm |
| Width | 4.4mm |
| Thickness | 1mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UCC28084PWG4 Overview
In the 8-TSSOP (0.173, 4.40mm Width) package, the switching controller meets most application requirements. For outputs of 2, this dc motor controller is suitable. PMIC packaging is solid with a Tray enclosure. Transistor Driver dc switching's outputs (s) are supported. dc controls with 4.1V~15V voltage are supplied and operated. Workable in an dc switcher where -40°C~85°C TA is the -40°C~85°C TArm. Using this switching controller, it is possible to switch at 200kHz. The Surface Mount makes it ideal for general dc dc regulator. Switching control is made easier with the dcdc regulator's Current Limit, Frequency Control. The switch converters are connected to a SWITCHING CONTROLLER analog IC. switching converters terminal (s) are designed to be at DUAL. The 8 terminations can be used for a wide range of dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 10V is input. In addition to "UCC28084", there are other relevant dc to dc converter ics you can find. Total pins of switching converter are 8. Switching converter is a special type of Switching Regulator or Controllers. This dc dc voltage regulator should be powered by a voltage of 4.3V. Statistically, DC regulator outputs 500mV volts. If you are starting a new project, you should note the dc dc regulator's typical output current is 1A. The duty cycle of the voltage regulator dc to dc can be set to 50 % on power-up or power-down to ensure reliability. Switching controller operates at a frequency of 1MHz.
UCC28084PWG4 Features
Transistor Driver Outputs
Switching Frequency: 200kHz
Current Limit, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
Frequency: 1MHz
UCC28084PWG4 Applications
There are a lot of Texas Instruments UCC28084PWG4 DC to DC converter applications.
- Electric water heaters
- Solar power plants
- Pipe bending machines
- Surge protection circuits
- Cutting machine tools
- Precision electronic equipment
- Wide-range voltage regulation circuits
- Planers
- Automatic plug-in machines
- Direct power supply system
