UCC28086P
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Weight | 523.190449mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Frequency | 1MHz |
| Base Part Number | UCC28086 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 500mV |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 10V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 4.1V~15V |
| Control Features | Current Limit, Frequency Control |
| Input Voltage (Min) | 4.3V |
| Topology | Half-Bridge, Push-Pull |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 200kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 25ns |
| Synchronous Rectifier | Yes |
| Fall Time (Typ) | 25 ns |
| Max Duty Cycle | 50 % |
| Duty Cycle (Max) | 49% |
| Clock Sync | No |
| Output Phases | 1 |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UCC28086P Overview
This switching controller fits most application requirements since it is packaged in a 8-DIP (0.300, 7.62mm) package. There is sufficient capacity to generate switching controller for outputs 2. Tube solid enclosure protects the pmic. Transistor Driver dc switching's outputs (s) are supported. The supply and operating voltage of the dc control are 4.1V~15V. Suitable for a -40°C~85°C TA dc switcher. It can switch at 200kHz. The Through Hole allows it to be used for dc dc regulator in general. For efficient switching control, the dcdc regulator features Current Limit, Frequency Control. Connected to a SWITCHING CONTROLLER analog IC, the switch converters are connected to a power supply. DUAL are the position of the terminal of the switching converters. Different dc switching's functions can be applied to 8 terminations. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. There is a DC switcher's nominal voltage of 10V. Other relevant dc to dc converter ics can be found by searching "UCC28086". Pins number 8 of switching converter in total. In particular, switching converter is a type of Switching Regulator or Controllers. Input voltage of dc dc voltage regulator must be 4.3V. According to the test statistics, DC regulator outputs 500mV voltage. The dc dc regulator's usual output current is 1A, which should be noted down when you start a project. Voltage regulator dc to dc is designed to operate at 50 % duty cycle during power-ups and power-downs to ensure reliability. Switching controller operates at 1MHz Hz.
UCC28086P Features
Transistor Driver Outputs
Switching Frequency: 200kHz
Current Limit, Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
Frequency: 1MHz
UCC28086P Applications
There are a lot of Texas Instruments UCC28086P DC to DC converter applications.
- Alternators
- Smoke exhaust equipment
- Linear guide
- Power supplies of electronic gadgets
- Various precision measuring instruments
- Wide-range voltage regulation circuits
- Direct power supply system
- Communication system
- Current source circuits
- Digital precision reference circuits
