UCC2808AN-2
| Parameters | |
|---|---|
| Input Voltage (Min) | 4.3V |
| Topology | Push-Pull |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 194kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 25ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 25 ns |
| Max Duty Cycle | 50 % |
| Duty Cycle (Max) | 49% |
| Output Phases | 1 |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 523.190449mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Supply Voltage | 10V |
| Frequency | 1MHz |
| Base Part Number | UCC2808 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 500mV |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 10V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Nominal Supply Current | 1mA |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 4.1V~15V |
| Control Features | Frequency Control |
UCC2808AN-2 Overview
The switching controller fits in the 8-DIP (0.300, 7.62mm) package and is ideal for most applications. This dc motor controller can be used to generate outputs with 2 numbers. There is a Tube solid enclosure around the pmic. It is capable of dealing with Transistor Driver dc switching's output (s). dc switching'sDC control operates at 4.1V~15V volts and has 4.1V~15V supply voltage. Worked in an dc switcher with a -40°C~85°C TA rating. There is a switch at 194kHz that can be used with this controller. dc dc regulator is made easier with Through Hole. Featured in the dcdc regulator is Frequency Control which allows efficient switching control. An analog IC with the SWITCHING CONTROLLER signal is connected to the switch converters. There are a DUAL terminal on the switching converters. An array of 8 terminations of dc switching. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's voltage input of 10V. A search for "UCC2808" will reveal other relevant dc to dc converter ics. Total pins of switching converter are 8. Switching converter type is specifically Switching Regulator or Controllers. 4.3V should be the minimum input voltage for the dc dc voltage regulator. DC regulator outputs 500mV voltage based on test statistics. You should note down the dc dc regulator's usual output current of 100mA when you start a project. During power-up and power-down, the maximum duty cycle of the voltage regulator dc to dc is set to 50 %. Because of DC switcher's Through Hole, it is suitable for most prototype designs and applications. Switching controller operates at 1MHz Hz. Voltage 10V must be supplied. There is 1mA nominal current supply for this the controllers dc.
UCC2808AN-2 Features
Transistor Driver Outputs
Switching Frequency: 194kHz
Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
Frequency: 1MHz
UCC2808AN-2 Applications
There are a lot of Texas Instruments UCC2808AN-2 DC to DC converter applications.
- Adjustable voltage or current linear circuits
- Geothermal power
- Low output voltage switching power supply circuits
- Electrical distribution systems
- Magnetohydrodynamic power
- Mobile phones
- Digital display device
- Handheld GPS
- Correction machines
- Smoke exhaust equipment
