UCC2892PWR
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Weight | 61.887009mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.65mm |
| Frequency | 1MHz |
| Base Part Number | UCC2892 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 11.1V |
| Output Type | Transistor Driver |
| Operating Supply Voltage | 12V |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive, Isolation Capable |
| Output Current | 150mA |
| Voltage - Supply (Vcc/Vdd) | 8.5V~16V |
| Control Features | Current Limit, Enable, On Time Control, Ramp, Soft Start |
| Topology | Flyback, Forward Converter |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 250kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 19ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 14 ns |
| Nominal Input Voltage | 110V |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 73 % |
| Duty Cycle (Max) | 70% |
| Clock Sync | Yes |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UCC2892PWR Overview
It comes in a 16-TSSOP (0.173, 4.40mm Width) package, so switching controller can be used for most applications. dc motor controller is suitable for 1 output generation. A solid enclosure of Tape & Reel (TR) surrounds pmic. It is capable of handling Transistor Driver dc switching's outputs (s). DC control operates at 8.5V~16V volts and has 8.5V~16V supply voltage. Suitable for working in an dc switcher that has a -40°C~85°C TA. This switching controller can switch at 250kHz. dc dc regulators can be carried out with Surface Mount. Featured in the dcdc regulator is Current Limit, Enable, On Time Control, Ramp, Soft Start which allows efficient switching control. SWITCHING CONTROLLER analog IC connects the switch converters. DUAL are the position of the terminal of the switching converters. A variety of 16 terminations are available in dc switching. Some of the control techniques used by these dc dc converter ics are PULSE WIDTH MODULATION. DC switcher's voltage input of 12V. You can find other relevant dc to dc converter ics by searching "UCC2892". Total pins of switching converter are 16. In particular, switching converter is a type of Switching Regulator or Controllers. A 11.1V voltage of DC regulator was detected in the test statistics. normally, the dc dc regulator's output current is 150mA, which you should keep in mind when starting a project. The duty cycle of the voltage regulator dc to dc can be set to 73 % on power-up or power-down to ensure reliability. Switching controller operates at 1MHz Hz. It is suggested that users apply 12V to the voltage regulator dc to dc in order to run it safely and reliably in a circuit. 110V is the nominal working voltage.
UCC2892PWR Features
Transistor Driver Outputs
Switching Frequency: 250kHz
Current Limit, Enable, On Time Control, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 73 %
Frequency: 1MHz
UCC2892PWR Applications
There are a lot of Texas Instruments UCC2892PWR DC to DC converter applications.
- Analog precision reference circuits
- Combined machine tools
- Adjustable voltage or current linear circuits
- Digital display device
- Electric water heaters
- Computer rooms
- Grinders
- Television equipment
- Precision electronic equipment
- Wide-range voltage regulation circuits
