UCC3580N-1
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Weight | 1.053808g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Frequency | 1MHz |
| Base Part Number | UCC3580 |
| Function | Step-Up/Step-Down |
| Number of Outputs | 2 |
| Output Voltage | 400mV |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 12V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 100mA |
| Voltage - Supply (Vcc/Vdd) | 8.5V~16V |
| Quiescent Current | 2.5mA |
| Control Features | Enable, Ramp, Soft Start |
| Topology | Forward Converter |
| Control Mode | VOLTAGE-MODE |
| Frequency - Switching | 400kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 40ns |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 20 ns |
| Switcher Configuration | PUSH-PULL |
| Max Duty Cycle | 69 % |
| Duty Cycle (Max) | 66% |
| Output Phases | 1 |
| Height | 4.57mm |
| Length | 19.3mm |
| Width | 6.35mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
UCC3580N-1 Overview
The switching controller fits in the 16-DIP (0.300, 7.62mm) package and is ideal for most applications. It is sufficient to generate 2 outputs with this dc motor controller. PMIC is packaged in a solid enclosure of Tube. The system can process Transistor Driver dc switching's outputs (s). 8.5V~16V is the supply voltage and the operating voltage of the dc control. Work well in dc switchers with a 0°C~70°C TA. Using this switching controller, it is possible to switch at 400kHz. The Through Hole value makes it suitable for general dc dc regulator. DCDC regulator is controlled efficiently by Enable, Ramp, Soft Start. The switch converters are connected to an analog IC with a SWITCHING CONTROLLER output. There are a DUAL terminal on the switching converters. The 16 terminations can be used for a wide range of dc switching. These dc dc converter ics adapt a variety of control techniques, including PULSE WIDTH MODULATION. A DC switcher's nominal voltage of 12V is input. A search for "UCC3580" will reveal other relevant dc to dc converter ics. 16 pins are on switching converter. Switching converter is a special type of Switching Regulator or Controllers. Statistically, the DC regulator outputs 400mV voltage. The dc dc regulator's usual output current is 100mA, which should be noted down when you start a project. Power-up and power-down reliability is ensured voltage regulator dc to dc by setting the maximum duty cycle to 69 %. DC switcher's Through Hole makes it qualified for most application and prototype designs. DC switcher'sA frequency of 1MHz is set for the switching controller. In a dormant state, the dc switching uses 2.5mA.
UCC3580N-1 Features
Transistor Driver Outputs
Switching Frequency: 400kHz
Enable, Ramp, Soft Start
PULSE WIDTH MODULATION
Max Duty Cycle: 69 %
Frequency: 1MHz
UCC3580N-1 Applications
There are a lot of Texas Instruments UCC3580N-1 DC to DC converter applications.
- Textile machinery
- Network technology
- Electrical distribution systems
- Refrigerators of central air conditioners
- Low output voltage switching power supply circuits
- Die casting equipment
- Series voltage regulation circuits
- Imported equipment
- Medical equipment
- Handheld GPS
