UCC3800NG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Weight | 523.190449mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Supply Voltage | 10V |
| Terminal Pitch | 2.54mm |
| Frequency | 1MHz |
| Base Part Number | UCC3800 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 1V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 10V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 6.9V~12V |
| Control Features | Frequency Control |
| Input Voltage (Min) | 7.5V |
| Topology | Buck, Boost, Flyback, Forward Converter |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 46kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 41ns |
| Supply Current-Max (Isup) | 25mA |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 44 ns |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 100 % |
| Duty Cycle (Max) | 99% |
| Height | 5.08mm |
| Length | 9.81mm |
| Width | 6.35mm |
| Thickness | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UCC3800NG4 Overview
Capsuled in the 8-DIP (0.300, 7.62mm) package, the switching controller can be used for a wide range of applications. It is sufficient to generate 1 outputs with this dc motor controller. A solid enclosure of Tube surrounds pmic. Transistor Driver dc switching's outputs (s) can be handled by it. The supply and operating voltage of the dc control are 6.9V~12V. Workable in an dc switcher where 0°C~70°C TA is the 0°C~70°C TArm. It can switch at 46kHz. As it has a Through Hole value, it can be used for general dc dc regulator. Frequency Control is used for efficient switching control in the dcdc regulator. Switch converters are connected to ICs with SWITCHING CONTROLLER analog outputs. A switching converters's terminal (s) sits at the DUAL position. The 8 terminations can be used for a wide range of dc switching. The control methods that these dc dc converter ics use include PULSE WIDTH MODULATION. DC switcher's input voltageis set to 10V. Other relevant dc to dc converter ics can be found by searching "UCC3800". 8 pins are on switching converter. Specially, switching converter corresponds to type Switching Regulator or Controllers. Input voltage of dc dc voltage regulator must be 7.5V. The test statistics indicate that DC regulator outputs a voltage of 1V. If you start a project, note down the dc dc regulator's usual output current of 1A. It is set to 100 % duty cycle to ensure voltage regulator dc to dc reliability during power-ups and power-downs. DC switcher's Through Hole makes it qualified for most application and prototype designs. DC switcher'sSwitching controllers operate at 1MHz frequencies. This voltage controller requires a supply voltage of 10V. There should be 25mA current exceeding 25mA supplied to the controller.
UCC3800NG4 Features
Transistor Driver Outputs
Switching Frequency: 46kHz
Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 100 %
Frequency: 1MHz
UCC3800NG4 Applications
There are a lot of Texas Instruments UCC3800NG4 DC to DC converter applications.
- Domestic water pumps
- Servo drive system
- Sink circuits
- Surge protection circuits
- Window air conditioners
- Bending machines
- Packaging
- Grinders
- Series voltage regulation circuits
- PSRR circuits
