UCC3801DTRG4
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Switching Regulator or Controllers |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 10V |
| Frequency | 1MHz |
| Base Part Number | UCC3801 |
| Function | Step-Up, Step-Down, Step-Up/Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 1V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 10V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | 7.4V~12V |
| Control Features | Frequency Control |
| Topology | Buck, Boost, Flyback, Forward Converter |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 46kHz |
| Control Technique | PULSE WIDTH MODULATION |
| Rise Time | 41ns |
| Supply Current-Max (Isup) | 30mA |
| Synchronous Rectifier | No |
| Fall Time (Typ) | 44 ns |
| Switcher Configuration | SINGLE |
| Max Duty Cycle | 50 % |
| Duty Cycle (Max) | 49% |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
UCC3801DTRG4 Overview
In the 8-SOIC (0.154, 3.90mm Width) package, the switching controller meets most application requirements. For 1 outputs, the dc motor controller is appropriate. An enclosure of Tape & Reel (TR) is used to package the PMIC. Transistor Driver dc switching's outputs (s) are supported. DC control operates at 7.4V~12V volts and has 7.4V~12V supply voltage. Workable in an dc switcher where 0°C~70°C TA is the 0°C~70°C TArm. The switching controller is capable of switching at the 46kHz position. As it has a Surface Mount value, it can be used for general dc dc regulator. Frequency Control is used for efficient switching control in the dcdc regulator. SWITCHING CONTROLLER analog IC connects the switch converters. A switching converters's terminal (s) sits at the DUAL position. An array of 8 terminations of dc switching. A few of the control techniques these dc dc converter ics adapt include PULSE WIDTH MODULATION. DC switcher's input voltageis set to 10V. In addition to "UCC3801", there are other relevant dc to dc converter ics you can find. There are only 8 pins on switching converter. Switching converter type is specifically Switching Regulator or Controllers. As determined by the test statistics, the output voltage of DC regulator is 1V. You should note that the dc dc regulator's usual output current is 1A. It is set to 50 % duty cycle to ensure voltage regulator dc to dc reliability during power-ups and power-downs. Because of DC switcher's Surface Mount, it is suitable for most prototype designs and applications. Switching controller operates at 1MHz Hz. There must be a voltage supply of 10V volts. It is not recommended to supply more current to the controller than 30mA.
UCC3801DTRG4 Features
Transistor Driver Outputs
Switching Frequency: 46kHz
Frequency Control
PULSE WIDTH MODULATION
Max Duty Cycle: 50 %
Frequency: 1MHz
UCC3801DTRG4 Applications
There are a lot of Texas Instruments UCC3801DTRG4 DC to DC converter applications.
- CMM
- seismic instrument power circuits
- Alternators
- Linear guide
- Balance equipment
- Electric heating, lighting
- Wind power
- Ball screw pair
- Electrical distribution systems
- Computer rooms
