UDN2916LBTR
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 24-SOIC (0.295, 7.50mm Width) |
| Operating Temperature | -20°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 24 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Applications | General Purpose |
| Additional Feature | ALSO REQUIRES 10V TO 45V VBB SUPPLY |
| HTS Code | 8542.39.00.01 |
| Subcategory | Motion Control Electronics |
| Voltage - Supply | 4.75V~5.25V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | UDN2916 |
| JESD-30 Code | R-PDSO-G24 |
| Function | Driver - Fully Integrated, Control and Power Stage |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 5.25V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.75V |
| Interface | Parallel |
| Analog IC - Other Type | STEPPER MOTOR CONTROLLER |
| Output Configuration | Half Bridge (4) |
| Current - Output | 750mA |
| Supply Current-Max (Isup) | 50mA |
| Voltage - Load | 10V~45V |
| Motor Type - AC, DC | Brushed DC |
| Motor Type - Stepper | Bipolar |
| Height Seated (Max) | 2.65mm |
| Length | 15.4mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
UDN2916LBTR Overview
Drivers controllers is designed wDrivers controllersh a package of [0].Drivers controllers is packaged wDrivers controllersh a 24-SOIC (0.295, 7.50mm Width) case.The part should be mounted by Surface Mount.I believe it would be suitable for the component connected to General Purpose.There is a capability for the device to provide 4.75V~5.25V volts.Drivers controllers operates wDrivers controllershin a range of -20°C~150°C TJdegrees Celsius.Drivers controllers is possible to categorize the motor type as Brushed DC.A total of 24terminations are available in this part.You can apply voltage at 10V~45Vto the load.Please take in mind that this amplifier should be run at 5V.There is a recommended mounting method of Surface Mount.The output current should be kept at 750mA for the part.There is an analog integrated circuit STEPPER MOTOR CONTROLLERpresent in the device.The UDN2916part number is used to locate the part.The Motion Control Electronicsseries includes this item.A characteristic ALSO REQUIRES 10V TO 45V VBB SUPPLYis also associated with it.
UDN2916LBTR Features
Applications : General Purpose
Load voltage across the chip 10V~45V
base on UDN2916 number
Additional Feature: ALSO REQUIRES 10V TO 45V VBB SUPPLY
UDN2916LBTR Applications
There are a lot of Allegro MicroSystems UDN2916LBTR motor drivers applications.
- High brightness LED lighting
- Commercial office
- Step-up or step-down driver topologies
- Tail lights
- General lighting
- CHMSL (center high-mount stop lamps)
- Lighting for the ambience of tunability
- A cross between entertainment
- Automotive exterior and interior lighting
- RGB and monochromatic LED drivers for signage and traffic signals
