USB1T11AM
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | LIFETIME (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Weight | 150mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | USB1T11A |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Interface | Serial |
| Operating Supply Current | 5mA |
| Number of Ports | 2 |
| Nominal Supply Current | 5mA |
| Output Current | 4mA |
| Number of Bits | 1 |
| Family | USB |
| Data Rate | 12Mbps |
| Output Characteristics | 3-STATE |
| Nominal Input Voltage | 2V |
| Output Polarity | TRUE |
| Protocol | USB 1.1 |
| Number of Drivers/Receivers | 1/1 |
| Propagation Delay (tpd) | 300 ns |
| Duplex | Half |
| ESD Protection | Yes |
| Number of Receivers | 1 |
| Height | 1.5mm |
| Length | 8.75mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
USB1T11AM Overview
This driver chip is excellent for driving common LEDs due to its enhanced 14-SOIC (0.154, 3.90mm Width) package.Tube package is used for this receiver.As a Transceiver can transceiver, this part has enabled many applications to be served.PCB or development board with Surface Mount-type connectors can accommodate this wide receiver.With respect to the power supply, this differential driver uses 3V~3.6V.At any given time, there can be up to 1/1 eligible receivers/drivers for this electronic part.IC receiver is designed for applications with a temperature of -40°C~85°C.With a voltage range of 3.3V, this driver IC can operate efficiently.Integrated into this wide receiver are 14 terminations that are used for driving and receiving signals from data.Since the base part number USB1T11A uniquely identifies the product type, temperature, package, etc., you can use it to find more variations.Wide receiver with enhanced power dissipation control, 14-pin.Its package size is drastically reduced by downsizing ICs and utilizing high-density Surface Mount mounting techniques.There is a 3.3V input voltage supply that can be used to operate this transceiver module.The module isolated transceiver contains 1 receivers.Input voltage is set to a value of 5mA, and this integrating circuit is capable of driving LEDs with that voltage.In order to avoid damaging this transceiver module, its manufacturer recommends using a supply voltage below 3.6V.To run this module isolated transceiver, you must supply it with at least 3V of voltage.This bluetooth transceiver provides an output current of 4mA.
USB1T11AM Features
Tube package
14 pins
USB1T11AM Applications
There are a lot of ON Semiconductor USB1T11AM Drivers/Receivers/Transceivers applications.
- IP cameras
- Wireless transmission
- transmission relay
- Cordless telephone
- Satellite ground stations
- Single to Multimode Fiber Conversion
- Switches
- Wireless projection application for conferences
- Datacom networking applications
- 1x/2x Fiber Channel
