USB1T20MTCX
| Parameters | |
|---|---|
| Driver Number of Bits | 1 |
| Duplex | Half |
| ESD Protection | Yes |
| Transmit Delay-Max | 300 ns |
| Output Low Current-Max | 0.004A |
| Number of Receivers | 1 |
| Out Swing-Min | 2.5 V |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 6 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 14 |
| Weight | 55.3mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2016 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Termination | SMD/SMT |
| ECCN Code | EAR99 |
| Type | Transceiver |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Line Driver or Receivers |
| Technology | CMOS |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | USB1T20 |
| Operating Supply Voltage | 3.3V |
| Interface | USB |
| Operating Supply Current | 5mA |
| Nominal Supply Current | 5mA |
| Data Rate | 12Mbps |
| Differential Output | YES |
| Protocol | USB 2.0 |
| Input Characteristics | DIFFERENTIAL |
| Number of Drivers/Receivers | 1/1 |
USB1T20MTCX Overview
This driver chip is excellent for driving common LEDs due to its enhanced 14-TSSOP (0.173, 4.40mm Width) package.Tape & Reel (TR) package is used for this receiver.It has proved to be a valuable component for a variety of applications since it is a Transceiver can transceiver.Ideally, you should place this wide receiver on a Surface Mount-type PCB or development board.A differential driver like this uses 3V~3.6V of power.As many as 1/1 eligible receivers/drivers can be used simultaneously with this electronic part.As its name implies, this ic receiver is designed for applications where -40°C~85°C is the operating temperature.There is a voltage range of 3.3V for this line driver ic, so it can operate efficiently.The integrated terminations of this wide receiver allow it to drive and receive signals from data.Since the base part number USB1T20 describes the product type, temperature, package, etc., you might get more options by searching with it.Wide receiver with enhanced power dissipation control, 14-pin.This package size decreases dramatically due to optical transceiver downsizing and high-density Surface Mount mounting technologies.In terms of resolution, this ic receiver was capable of providing a 1-bit resolution.This transceiver module is designed to operate from an input voltage supply of 3.3V.A Line Driver or Receivers subcategory can be assigned to this rf transceiver module.In addition to that, it contains 1 receivers as well.With an input voltage of 5mA, this integrating circuit has the ability to drive LEDs with an output voltage of 5mA.
USB1T20MTCX Features
Tape & Reel (TR) package
14 pins
USB1T20MTCX Applications
There are a lot of ON Semiconductor USB1T20MTCX Drivers/Receivers/Transceivers applications.
- Shortwave receiver
- VoIP phones
- Routers
- Automation systems
- Satellite communication
- Single fiber bidirectional application
- Wireless interactive experience
- Single to Multimode Fiber Conversion
- Satellite ground stations
- Home theater wiring-free
