Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
ACTIVE (Last Updated: 7 months ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
PowerSSO-12 |
Number of Pins |
12 |
Operating Temperature |
-40°C~150°C TJ |
Packaging |
Tape & Reel (TR) |
Series |
VIPower™ |
JESD-609 Code |
e3 |
Feature |
Auto Restart |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
12 |
ECCN Code |
EAR99 |
Resistance |
25mOhm |
Terminal Finish |
Matte Tin (Sn) - annealed |
Subcategory |
Peripheral Drivers |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
13V |
Terminal Pitch |
0.8mm |
Base Part Number |
VN5E025 |
Pin Count |
12 |
Number of Outputs |
1 |
Output Type |
N-Channel |
Max Output Current |
60A |
Operating Supply Voltage |
13V |
Supply Voltage-Max (Vsup) |
28V |
Power Supplies |
8/28V |
Interface |
On/Off |
Nominal Supply Current |
1.5mA |
Output Configuration |
High Side |
Voltage - Supply (Vcc/Vdd) |
Not Required |
Max Supply Current |
3mA |
Input Type |
Non-Inverting |
Turn On Delay Time |
15 μs |
Switch Type |
General Purpose |
Output Current per Channel |
43A |
Turn-Off Delay Time |
40 μs |
Ratio - Input:Output |
1:1 |
Voltage - Load |
4.5V~28V |
Driver Number of Bits |
1 |
Fault Protection |
Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
Rds On (Typ) |
25m Ω (Max) |
Built-in Protections |
TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
Output Current Flow Direction |
SINK |
Length |
4.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
VN5E025AJTR-E Overview
The LED driver's packaged as a Tape & Reel (TR).It is included with the PowerSSO-12 package as well.This LED driving board is mounted using the mounting type Surface Mount.General Purpose is the switch type it owns.It is recommended that the temperature be set to -40°C~150°C TJ for reliable performance.It is possible to use 1 outputs in the lighting driver.The LED driving board operates at Not Required volts.The maximum output voltage is N-Channel volts.As far as features are concerned, the LED driving board has Auto Restart.It is part of the VN5E025 family of LED drivers.The termination count is 12.The 12 pins are used for the operation of the system.Currently, there are 1 functions associated with the lighting driver.This results in the maximum output current dropping to 60A to meet the operation criteria.The supply voltage of 13V is conducive to high efficiency.This lighting driver is mounted in the way of Surface Mount.As a result, it has a total of 12 pins.It has 25mOhm resistance.There is an electrical component included in the VIPower? series.There is a Peripheral Drivers capacity container for this LED driver that is self-contained.In this LED driver, the maximum supply voltage is configured to be 28V (Vsup).This part's power supply is 8/28V.The supply voltage should be set at 13V for best efficiency.For its operation, a maximum current requirement of 3mA is required.
VN5E025AJTR-E Features
Supplied from 13V
Resistance of 25mOhm
VN5E025AJTR-E Applications
There are a lot of STMicroelectronics VN5E025AJTR-E Power Switches ICs applications.
- USB Power Distribution
- Storage (HDDs, SSDs)
- Hot Swap
- Various applications equipped with buttons
- Portable/Handheld Devices
- Wireless/Networking Cards
- Low Voltage I/O System Power
- Hot Swap
- Telecom and Network Systems
- Smart Phones, Feature Phones