VN5E050AJTR-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSSO-12 |
| Number of Pins | 12 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tape & Reel (TR) |
| Series | VIPower™ |
| JESD-609 Code | e3 |
| Feature | Auto Restart |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 12 |
| ECCN Code | EAR99 |
| Resistance | 50mOhm |
| Terminal Finish | MATTE TIN |
| Subcategory | Peripheral Drivers |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.8mm |
| Base Part Number | VN5E050 |
| Pin Count | 12 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 27A |
| Operating Supply Voltage | 13V |
| Supply Voltage-Max (Vsup) | 28V |
| Power Supplies | 8/28V |
| Interface | On/Off |
| Nominal Supply Current | 1.5mA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 3mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 20 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 19A |
| Turn-Off Delay Time | 40 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4.5V~28V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage |
| Rds On (Typ) | 50m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VN5E050AJTR-E Overview
The package is in the form of a Tape & Reel (TR).This package is included in PowerSSO-12.Surface Mount is the mounting type of the LED driver.General Purpose is the type of switch owned by it.The temperature should be set to -40°C~150°C TJ to ensure reliable functioning.It is possible to use 1 outputs in the lighting driver.A voltage of Not Required is used to power it.A maximum output voltage of N-Channel volts can be obtained with this LED driver.In terms of features, the LED driving board has Auto Restart.The VN5E050 family consists of this type.It contains 12 terminations.The 12 pins are used to operate the LED driver.It contains 1 functions.The maximum output current must drop to 27A to meet the operation criteria.The supply voltage of 13V is conducive to high efficiency.As a result, it is mounted in the manner of Surface Mount.A total of 12 pins are included in this LED driver.It has 50mOhm resistance.This electrical component is part of the VIPower? series.Self-contained LED driver with Peripheral Drivers capacity in an econtainer.The maximum supply voltage for this LED driver is 28V (Vsup).The power supply of the part is 8/28V.A supply voltage of 13V is recommended for maximum efficiency.For its operation, a maximum current requirement of 3mA is required.
VN5E050AJTR-E Features
Supplied from 13V
Resistance of 50mOhm
VN5E050AJTR-E Applications
There are a lot of STMicroelectronics VN5E050AJTR-E Power Switches ICs applications.
- Hot Swaps
- Portable GPS Device
- Solid State Drivers
- Handheld Devices
- Portable Video Game Players
- PDAs
- Hot Swap
- Low Voltage I/O System Power
- Wireless Modem Data Cards
- Notebook and Tablet Computers
