VN7040AJTR-E
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-PowerLFSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Cut Tape (CT) |
| Series | VIPower™ |
| Feature | Auto Restart, Status Flag |
| Part Status | Discontinued |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Terminal Pitch | 0.5mm |
| Base Part Number | VN7040 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Max Output Current | 24A |
| Supply Voltage-Max (Vsup) | 28V |
| Supply Voltage-Min (Vsup) | 4V |
| Interface | On/Off |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 5mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 120 μs |
| Switch Type | General Purpose |
| Turn-Off Delay Time | 100 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 4V~28V |
| Fault Protection | Current Limiting (Fixed), Open Load Detect, Over Temperature, Over Voltage, UVLO |
| Rds On (Typ) | 40m Ω |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Output Current Flow Direction | SINK |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VN7040AJTR-E Overview
Cut Tape (CT) is how it's packaged.This file is included in package 16-PowerLFSOP (0.154, 3.90mm Width).In this case, the LED driving board is mounted as Surface Mount.General Purpose is the type of switch owned by it.It is recommended that the temperature be set to -40°C~150°C TJ for reliable operation.The LED driver has a total of 1 outputs.With a supply voltage of Not Required, the LED driving board operates.The maximum output voltage of this LED driver is N-Channel volts.Auto Restart, Status Flag features are available on the lighting driver.I believe it belongs to the VN7040 family.In total, there are 16 terminations.For operation, we use the 16 pins.It is important to note that the LED driving board has 1 functions.The maximum output current is reduced to 24A to meet the operation criteria.High efficiency is possible at 13V supply voltage.Surface Mount is mounted in the way of this LED driving board.It belongs to the VIPower? series.The lighting driver is configured to have a maximum supply voltage of 28V (Vsup).In order for the lighting driver to operate normally, the supply voltage (Vsup) should be maintained above 4V.It requires 5mA current to operate.
VN7040AJTR-E Features
Supplied from 13V
VN7040AJTR-E Applications
There are a lot of STMicroelectronics VN7040AJTR-E Power Switches ICs applications.
- Wireless Modem Data Cards
- Storage Drives
- Hard Disk Drives
- Portable GPS
- Wearable Devices
- Various applications equipped with buttons
- Storage (HDDs, SSDs)
- Hot-Swap Systems
- USB Ports/Hubs
- Low Voltage I/O System Power
