VN808-32-E
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 8 months ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 36-BSSOP (0.433, 11.00mm Width) Exposed Pad |
| Number of Pins | 36 |
| Operating Temperature | -40°C~125°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| Feature | Auto Restart, Status Flag |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 36 |
| ECCN Code | EAR99 |
| Resistance | 150mOhm |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 96W |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 8 |
| Supply Voltage | 24V |
| Terminal Pitch | 0.65mm |
| Base Part Number | VN808 |
| Pin Count | 36 |
| Number of Outputs | 8 |
| Output Type | N-Channel |
| Max Output Current | 1A |
| Operating Supply Voltage | 24V |
| Supply Voltage-Max (Vsup) | 45V |
| Power Supplies | 10.5/32V |
| Interface | On/Off |
| Nominal Supply Current | 12mA |
| Output Configuration | High Side |
| Power Dissipation | 96W |
| Output Current | 1A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 12mA |
| Input Type | Non-Inverting |
| Turn On Delay Time | 100 μs |
| Switch Type | General Purpose |
| Output Current per Channel | 1A |
| Rise Time | 50μs |
| Turn-Off Delay Time | 150 μs |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 10.5V~45V |
| Driver Number of Bits | 8 |
| Fault Protection | Current Limiting (Fixed), Over Temperature |
| Rds On (Typ) | 150m Ω |
| Built-in Protections | TRANSIENT; THERMAL; UNDER VOLTAGE |
| Height | 3.3mm |
| Length | 16mm |
| Width | 11.1mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
VN808-32-E Overview
It is packaged in the form of a Tube.There is a package for it in the 36-BSSOP (0.433, 11.00mm Width) Exposed Pad package.The lighting driver has the mounting type Surface Mount.General Purpose is the switch type it owns.Keeping the temperature at -40°C~125°C TJ ensures reliable operation.By default, it is set to output 8.Operation is based on a supply voltage of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.There are Auto Restart, Status Flag features available on the LED driving board.This object belongs to the VN808 family.It contains 36 terminations.36 pins are used for operation.The LED driving board has a total of 8 functions.As a result, the maximum output current is reduced to 1A in order to meet the operation requirements.Supply voltages of 24V allow for high efficiency.Surface Mount is mounted in the way of this LED driving board.There are 36 pins in total on this board.It has 150mOhm resistance.This electrical component is included in the VIPower? series.In this case, the output current is set to 1A.Self-contained in an econtainer with a capacity of Peripheral Drivers, this LED driver is self-contained.The LED driver is configured with a maximum supply voltage of 45V (Vsup).This part is powered by 10.5/32V.It is recommended that the supply voltage be set at 24V in order to achieve maximum efficiency.It requires 12mA current to operate.
VN808-32-E Features
Supplied from 24V
Resistance of 150mOhm
VN808-32-E Applications
There are a lot of STMicroelectronics VN808-32-E Power Switches ICs applications.
- Solid-State Drives
- PDAs
- Smart Phones, Feature Phones
- Portable GPS Device
- PC Card Hot Swap
- Low Voltage I/O System Power
- Wearable Devices
- Set-Top Boxes
- Handheld Devices
- Hard Disk Drives
