VN920SP
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | PowerSO-10 Exposed Bottom Pad |
| Number of Pins | 10 |
| Operating Temperature | -40°C~150°C TJ |
| Packaging | Tube |
| Series | VIPower™ |
| JESD-609 Code | e0 |
| Feature | Auto Restart |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 15mOhm |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Peripheral Drivers |
| Max Power Dissipation | 96.1W |
| Technology | MOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 13V |
| Base Part Number | VN920 |
| Pin Count | 10 |
| Number of Outputs | 1 |
| Output Type | N-Channel |
| Operating Supply Voltage | 36V |
| Interface | On/Off |
| Nominal Supply Current | 5mA |
| Output Configuration | High Side |
| Power Dissipation | 96.1W |
| Output Current | 30A |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Max Supply Current | 25mA |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 5.5V |
| Max Input Voltage | 36V |
| Output Current per Channel | 45A |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 5.5V~36V |
| Driver Number of Bits | 1 |
| Fault Protection | Current Limiting (Fixed), Over Temperature, Over Voltage |
| Output Peak Current Limit-Nom | 45A |
| Rds On (Typ) | 15m Ω (Max) |
| Built-in Protections | TRANSIENT; OVER CURRENT; OVER VOLTAGE; THERMAL; UNDER VOLTAGE |
| Height Seated (Max) | 3.75mm |
| Length | 9.4mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
VN920SP Overview
It is package in Tube case.This file is included in package PowerSO-10 Exposed Bottom Pad.This LED driving board is mounted using the mounting type Surface Mount.It owns General Purpose switch type.In order to guarantee reliable performance, the temperature should be set to -40°C~150°C TJ.By default, it is set to output 1.In order to operate, it requires a voltage supply of Not Required.A maximum output voltage of N-Channel volts can be achieved by this LED driver.In terms of features, the LED driving board has Auto Restart.I believe it belongs to the VN920 family.It contains 10 terminations.The 10 pins are used for the operation of the system.It contains 1 functions.With a supply voltage of 13V, high efficiency is possible.In this case, it is mounted in the way of Surface Mount.10 pins are connected to it in total.It has 15mOhm resistance.This electrical component can be found in the VIPower? series.As a result, the output current is set to 30A.The LED driver is packaged in an econtainer with a capacity of Peripheral Drivers.Optimal efficiency requires a voltage of 36V.Input voltage is limited to 36V volts.Input voltage must be at least 5.5V volts.For its operation, a maximum current requirement of 25mA is required.
VN920SP Features
Supplied from 13V
Resistance of 15mOhm
VN920SP Applications
There are a lot of STMicroelectronics VN920SP Power Switches ICs applications.
- PDAs
- Set-top-box
- Hot Swap
- Solid-State Drives
- Wireless/Networking Cards
- Gaming
- Wearable Devices
- Storage Drives
- Various applications equipped with buttons
- PC Cards
